Table des Matières
Sommaire des Matières pour Sehan Electools YF Serie
- Page 1 Manual update history - 2014.12.30 p16, 17 correction / P14, P17 aded - 2015.03.31 pictures are replaced with double bearing type - 2015.04.28 page 19, I/O timing chart added - 2015.08.11 Replaced to the new models in specification on page 8...
- Page 2 April .08. 2016 Instruction Manual - YF series BLDC Screwdriver - Usage : Micro oven, Refrigerator, Washing Machine, Automobile & home appliances assembly...
-
Page 3: Table Des Matières
INDEX Contents Page 1. General safety rules (English) 2. Specific safety rules (English) 1. General safety rules (French) 2. Specific safety rules (French) 3. Screwdriver Set composition & features 4. Screwdriver 4.1 Specification 4.2 Available bit socket 4.3 Torque curve at maximum speed 4.4 Information by LED display 4.5 Dimensions 5. -
Page 4: General Safety Rules (English)
ENGLISH 1. GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury SAVE THIS INSTRUCTIONS 1.1 Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. -
Page 5: Specific Safety Rules (English)
Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. -
Page 6: Règles De Sécurité Géneralés
FRENCH 1. RÈGLES DE SÉCURITÉ GÉNERALÉS AVERTISSEMENT ! Vous devez lire et comprendre les instructions. Le non-respect, même partiel, des instructions ci-près entraîne un rispue de choc électrique, d`incendie et/ou de blessures graves CONSERVEZ CES INSTRUCTIONS 1.1 Aire de travail - Veillez à... -
Page 7: Sécurité Des Personnes
1.3 Sécurité des personnes - Restez alerte, concentrez-vous sur votre travail et faites preuve de jugement. N`utilisez pas un outil électrique si vous êtes fatigué ou souis l`influence de drogues, d`alcool ou de médicaments. Un instant d`inattention suffit pour entrainer des biessures graves. - Habillez-vous convenablement. -
Page 8: Réparation
- Soyez attentif à tout désalignement ou coincement des pièces en mouvnment, à tout bris ou à toute autre condition préjudiciable au bon fonctionnement de l`outil. Si vous constatez qu`un ouitl est endommagé, faites-le répqrer avant de vous en servir. De nombreux accidents sont causés par des outils en mauvais état. -
Page 9: Screwdriver Set Composition & Features
3. Screwdriver set composition and features Screwdriver set contains screwdriver, controller and cable. Information by LED display SH-14P-YF Cable (3m) ESD grip (Option) Flat groove ring for mounting Screwdriver Standard controller YFC-35D Main Feature ■ Long life time of BLDC motor (No Carbon brush ) ■... -
Page 10: Specification
4. Screwdriver 4.1 Specification Torque Weight Speed Model Screw Start Kgf.cm Refer to the 4.2 YF35N M2.6~M5 7-35 500-1,500 0.73 A, B YF50N M3~M6 Lever 10-50 400-1,100 0.73 A, B YF100N M4~M8 40-100 250-500 0.73 YF35NP M3~M6 7-35 500-1,500 0.73 A, B PUSH YF50NP... -
Page 11: Information By Led Display
YF50N, YF50NP, PYF50N, YFA50N YF100N, PYF100N, YFA100N 4.4 Information by LED display LED display Alarm Description Reset ● RED Light On-Off blink (0.5s) 1 Over Voltage (over 37V) Auto reset under 37V ● RED Light On-Off blink (0.5s) 2 Overload (8A / 0.5s) Auto reset after 5s ●... -
Page 12: Dimensions
4.5 Dimensions YF35N, YF50N, YF100N, YF35NP, YF50NP, YF100NP PYF35N, PYF50N, PYF100N - 10 -... - Page 13 ■ YFA35N, YFA50N, YFA100N - 11 -...
-
Page 14: Controller
5. Controller 5.1 specification Model YFC-35D CE by MET NRTL by MET Safety certificate (EC countries) (USA, Canada) Rated Input 230 VAC 50~60Hz, 2.5A 120 VAC 60Hz, 2.5A Rated Output 35 VDC ±5%, 140W Maximum output current 10 A Intermittent operation 10s On / 30s Off Dimensions 95(W) x 221(D) x 143(H) mm... -
Page 15: Dimensions
5.3 Dimensions 6. Operation 6.1 Key buttons There are 3 mode in circulation by pressing MODE button. Once it is logged in, it is effective until the power OFF. Auto Log-in Factory setting password :"0" Parameter button : MODE By pressing the MODE button, it circulate Auto, Log-in and Parameter mode. - Page 16 button Log-in is required for parameter setting with password Log-in Mode Initial password "0" can be changed on PYord Parameter Mode Cursor shift up to left at the Parameter mode button Auto(Work) Mode Select the next preset number Log-in & Password It increase the number up button time...
-
Page 17: Parameter Setting
6.2 Parameter setting 6.2.1 Driver model selecting ( ModEl ) .... P1 Choose one of the right model number between 30n, 45n, 90n, 35n, 50n and 100n for the connected screwdriver as below ; YF35N YF50N YF100N YF30N YF45N YF90N Model PYF35N PYF50N... - Page 18 6.2.7 Multi-sequence ( M_FSt ) .... P7 Available to program multi step operation in sequence. oFF : Disable on : Enable 6.2.8 Multi_1 : First angle in turn ( Frt.Ag) ..... P8 Angle setting for angle stop in turn from 0 to 9999 ( unit = 0.1 turn ) 6.2.9 Multi_2 : Second reverse angle for next step of operation ( rEV.Ag ) .....
-
Page 19: In/Out Interface
6.2.16 Parameter initialization to factory setting ( Pinit ) ..... P16 All parameter will be changed to it's original torque setting. Password is "77" 6.2.17 Display type ( dSP.ty ) .... P17 Display type in parameter mode 0 : by Character display 1 : Parameter no. -
Page 20: I/O Interface Port Details On Back Panel
7.2 I/O interface port details on back panel Pin no. In / Out Interface Torque Up Motor Run ⑤ ⑨ Out COM Remote Start Driver Lock ⑥ ① Reverse rotation In COM 7.3 I/O interface diagram YFC-35D 24V or 0 V 20mA TORQUE UP 20mA... -
Page 21: I/O Timing Chart
8. I/O timing chart 8-1 Fastening OK Remote start (IN) Motor run (OUT) Torque up (OUT) 100mS 8-2 Loosening Reverse (IN) Remote start (IN) Motor Motor run (OUT) Torque up (OUT) Driver lock Remote start (IN) Driver lock (IN) Motor run (OUT) Torque up (OUT) 100mS - 19 -... -
Page 22: Error Display
9. Error display The YFC-35D controller shows error code number when it detect any failure during operation. The error code are as below Code Description Trouble shooting Screwdriver not connected Check the cable connection SMPS fault. Turn off the power and On again after The power supply system will 1 min.