Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
This symbol indicates that the
machine is in conformance with
the applicable European directive.
SPECIAL INSTRUCTIONS
The disc cutter is designed to provide safe
and reliable service in operating conditions
corresponding with the instructions, but it
can present dangers for the user and risks
of damage, consequently regular on site
inspection is necessary to ensure :
• Perfect technical condition (use for the
purpose for which it is intended and
taking into account any risks, and cor-
rection of any malfunction detrimental
to safety).
• Use a diamond disk for cutting with
water (sawing new or old concrete, tar-
mac or asphalt). No other type of disk is
allowed (abrasive, saw, etc . . .).
• Competent staff (qualifications, age,
training) who have read and understood
the manual in detail before starting
work: any electrical, mechanical or
other problem should be investigated
by a qualified maintenance engineer
(electrician, maintenance manager,
approved dealer, etc . . .).
• That the warnings and instructions mar-
ked on the machine are followed (ade-
quate personal protection, correct use,
general safety instructions, etc).
• That no modification, transformation or
addition is detrimental to safety and that
it is carried out without prior authoriza-
tion from the manufacturer.
• Respect of the maintenance intervals
and periodical checks recommended.
• That only genuine spare parts are used
for repairs.
Instruction plate
MANUFACTURER
TYPE
TYPE
N° SERIE
ANNEE DE
FABRICATION
WEIGHT
MASSE UTILE
Kg
PUISSANCE
PLAGE DE
MAXI TOOL
Ø MAXI OUTIL.
mm
TENSION
BORE
Ø ALESAGE
mm
FREQUENCE
SPEED
T/MN - RPM
INT. UTIL.
FAILURE TO COMPLY WITH
THESE
WARNINGS
RESULT IN DEATH OR SERIOUS
BODILY INJURY.
DO
carefully read and understand all the
instructions before operating the saw.
DO
always keep all guards in place.
DO
aways wear safety approved hearing,
eye, head and respiratory protection.
DO
keep all parts of your body away from
the blade and all other moving parts.
DO
know how to stop the saw quickly in
case of an emergency.
DO
shut off the engine and allow it to cool
before refueling.
DO
inspect the blade, flanges and shafts
for damage before installing the
blade.
DO
use only blades marked with a maxi-
mum operating speed greater than
the blade shaft speed.
DO
use caution and follow the instruc-
tions when loading and unloading the
saw.
DO NOT allow other persons to be near
the saw when starting, refueling
or when cutting.
DO NOT run petrol or diesel engines in an
enclosed area unless there is
adequate ventilation.
DO NOT use damaged equipment or
blades.
DO NOT operate the saw in areas of
combustible material. Sparks
from the saw could cause a fire
or an explosion.
DO NOT allow blade exposure from the
guard to be over 180 degrees.
DO NOT leave the saw unattended with
SERIAL
the motor running.
FABRICATION
YEAR
kW
POWER
V
VOLTAGE
DO NOT operate the saw while under the
Hz
FREQUENCY
A
INTENSITY
influence of drugs or alcohol.
1
Use
• Use : sawing of fresh or old concrete and
coated materials (asphalt).
COULD
• Tools : Diamond Blades - Water cooled
Øx625xmm - Bore 25.4 mm, right
Øx625xmm - Bore 25.4 mm, left
(Information from your usual DIMAS sup-
plier)
DO
DO NOT
2
Technical specifications
• Depth of cut : 230 mm Ø 625
• Nominal weight (empty) :
310 to 340 kg (depending on version)
• Operating weight :
370 to 410 kg (depending on version)
• Dimensions (L x W x H) : 1460 x 800 x 1150 mm
• Blade shaft RPM : 1900
• Blade : Ø 450 to 625 mm
• Tank : 60 litres (25 minutes of use)
POWER
PRESSURE
MODEL
LEVEL
LEVEL
MODEL /
Lwa (dB)
Lpa (dB)
KW / BHP
EN ISO 3744
EN ISO 4871
HATZ
14,7/20
112
95
HONDA
17,7/24
108
91
Description of the machine
3
[FIG. 1]
1 - Steering column
2 - Speed control
3 - Column
4 - Water inlet vale
5A - Disk casing, right
5B - Disk casing, left
6A - Right-hand housing guard
6B - Left-hand housing guard
7 - Front guide
8 - Depth indicator
9 - Motor
10 - Belt guard
11 - Belt casing (5B)
12 - Belt tension
13 - Tank
14 - Water tank drain (8 minutes)
15 - Mains water inlet
16 - Fuel tank
17 - Emergency stop
18 - Block (shaft)
19 - Battery isolation switch
20 - Starting switch
AUTOMATIC ADVANCE
21 - Controller
22 - Control light
23 - Potentiometer
24 - Emergency stop
25 - Clutch lever
26 - Locking lever
HYDRAULIC LOWERING MECHANISM
27 - Handle
28 - Central hydraulic tank
Handling - Transport
4
(blade dismantled)
Switch off the disk prior to moving
the machine on jobsite.
• For positioning the saw on site, it is suffi-
cient to push it. It moves easily on its four
wheels, without switching on the motor.
• Parking brake : release the locking lever
(25) (see Fig. 1) to engage forward motion.
Remove the disk prior to hoisting,
loading, unloading and transporting
the machine on jobsite.
VIBRATION
LEVEL
NF
EN V 25349
0,72
0,42
14
Publicité
Table des Matières
