Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Operation
Included in this Package
Notice
Caution
Warning
Introduction
Intro
Operation
Included in this Package
You should find all of the following items in this package:
Installation
CB Transceiver
Secondary Icons
Microphone Bracket
Operating Manual
English
2
s
n
o
I c
n
a i
M
Customer
Warranty
Assistance
Customer
Assistance
Microphone
Notice
Caution
Warning
Transceiver Bracket
Intro
Introduction
Installation and Start-Up
Mounting and Connections
•
Select a location for the transceiver and microphone bracket that is convenient for
Secondary Icons
operation. In automobiles, the transceiver is usually mounted to the underneath of the
dash panel, with the microphone bracket beside it.
Transceiver Bracket
Secondary Icons
e r
m
o
s t
u
C
n
i o
a t
e r
p
O
y
n t
r a
a r
W
e
c
n
a
i s t
s s
A
CB Tranceiver
e r
m
o
s t
u
C
n
i o
a t
a l l
s t
I n
e
c
n
a
i s t
s s
A
Antenna Connector
s
n
i o
u t
a
C
e
i c
o t
N
g
n
n i
a r
W
Fuse Connection
e r
m
o
s t
u
C
n
i o
a t
e r
p
O
y
n t
r a
a r
W
e
c
n
a
i s t
s s
A
e r
m
o
s t
u
C
n
i o
a t
a l l
s t
I n
e
c
n
a
i s t
s s
A
Microphone Connector
s
n
i o
u t
a
C
e
i c
o t
N
g
n
n i
a r
W
NOTE
For improved CB radio performance, connect the radio power leads directly to the
vehicle battery. This helps to ensure the following: 1) reduces conducted power line noise
Main Icons
into radio by taking advantage of the mechanical ltering properties of the vehicle battery.
2) Using the correct wire gauge between the battery and radio, helps to minimize Voltage
drop to the radio transmitter section to maximize transmitter RF output power.
Operation
Customer
Warranty
Assistance
Mounting and Connections
Customer
Intro
Operation
Customer
Warranty
Installation
Assistance
Assistance
s
n
o
I c
n
a i
M
Customer
Installation
A universal mounting bracket is supplied along with self-tapping
Assistance
screws and star washers. The transceiver is held in the
Notice
Caution
Warning
universal mounting bracket by two thumb screws, permitting
adjustment at the most convenient angle.
o
t r
I n
To mount and connect your transceiver:
1. Hold the radio with mounting bracket in the exact
Notice
Caution
Warning
location desired. Remove the mounting bracket
and use it as a template to mark the location for
the mounting screws.
2. Drill necessary holes and secure mounting
Main Icons
n
o
I c
y
a r
d
n
o
c
e
S
bracket in location.
3. Connect the antenna cable plug to the re cep ta cle
marked "ANT" on the back of the unit.
4. Connect the red lead of the DC power cord
s
n
o
I c
n
a i
M
to an accessory 12 volt fuse.
Intro
Operation
Customer
Warranty
Assistance
5. Connect the black lead to the negative side
of the automobile. This is usually the chassis.
Any convenient location with good electrical
contact (remove paint) may be used.
Customer
Installation
Assistance
o
t r
I n
NOTE
Secondary Icons
Before installing the CB radio, visually check the vehicle
battery connections to determine which battery
terminal, positive or negative (positive is the larger of
Notice
Caution
Warning
the two) is grounded to the engine block (or chassis).
6. Mount the microphone bracket on right side of the transceiver
n
o
I c
y
a r
d
n
o
c
e
S
or near it using two screws supplied. When mount ing in an
automobile, place the bracket under the dash so the
microphone is readily accessible.
7. Attach the four pin microphone cable to receptacle
on front of unit and install unit in bracket securely.
•
3
Nothing Comes Close to a Cobra
®
Publicité
Chapitres
Table des Matières
