Assembly instructions
Adjustable Corner Shelf Unit 175 KG
Item no. 2368900
Intended use
The product is intended for storing loads of up to 175 kg per shelf. The shelves can be mounted at different
heights and fits in corners to maximize floorspace. The parts can be assembled to produce different setups
e.g. shelf, table.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for
purposes other than those described above, the product may be damaged. Improper use can furthermore
cause hazards such as injuries. Read the assembly instructions carefully and keep them. Make this product
available to third parties only together with its assembly instructions.
This product complies with the statutory national and European requirements. All company names and prod-
uct names are trademarks of their respective owners. All rights reserved.
Delivery contents
refer to section "Assembly, b) Installation (Figure 2) " for information about where the parts fit
during installation.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(9)
(10)
Up-to-date operating instructions
Download the latest operating instructions from our website www.conrad.com/downloads
or scan the printed QR code. Follow the instructions on the website.
Description of symbols
The symbol with an exclamation mark in a triangle indicates important instructions contained in
these operating instructions that must be followed.
The arrow symbol indicates special information and advice on operation.
x3
(8)
(11)
x6
Safety instructions
Read the assembly instructions
carefully and especially observe the
safety information. If you do not fol-
low the safety instructions and in-
formation on proper handling in this
assembly instructions, we assume
no liability for any resulting personal
injury or damage to property. Such
cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of
children and pets.
• Do not leave packaging material lying around
carelessly. These may become dangerous play-
ing material for children.
• To handle heavy loads, ask another person for
help, in order to avoid injuries (e.g. back injuries).
• Verify that the delivery content is complete before
assembling the product. Do not assemble the
product if the delivery content is not complete.
• Exercise caution when assembling the product!
The product has some sharp corners which pose
a risk of injury! There is also a risk of your fingers
getting caught.
• Only carry out the steps required for assembly.
Never attempt to modify or repair the product. Do
not make any modifications.
x6
• Perform the installation very carefully. Malfunc-
tions can cause expensive consequential dam-
age; there is also a risk of injury.
x10
• Do not overload the product. Observe the "Tech-
nical data".
• Distribute the load on the product as evenly as
possible.
x10
Required tools
Use the following accessories (not included) to assist with installation:
•
Work gloves
x4
Assembly options
You can set the product up in different ways for example:
a) Tables
x5
x5
x2
b) Shelf
Images below are of the same shelf setup from different angles.
x5
x4
• Always observe the maximum load capacity of
the surface.
• Place the product on a flat, stable surface only.
• Do not use the product as a climbing aid, e.g. as
ladder.
• Check the functioning of the product before start-
ing to work.
• In case of doubt, do not install the product your-
self; have a professional do it for you.
• Protect the product from extreme temperatures,
direct sunlight, strong jolts, high humidity, mois-
ture, flammable gases, vapours and solvents.
• If it is no longer possible to operate the product
safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer
be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor
ambient conditions or
- has been subjected to any serious transport-
related stresses.
• Please handle the product carefully. Jolts, im-
pacts or a fall even from a low height can damage
the product.
• Contact an expert if you are in doubt regarding
the function, safety or installation of the product.
• Maintenance, modifications and repairs are to be
performed exclusively by an expert or at a quali-
fied shop.
• If you have questions which remain unanswered
by these assembly instructions, contact our tech-
nical support service or other technical personnel.
•
Mallet
•
Flat screwdriver