Battery Replacement - F.F. Group SAFETY BOX Notice Originale

4 | English
English
THIS MANUAL CONTAINS IMPORTANT INFORMA-
TION REGARDING THE OPERATION AND MAIN-
TENANCE OF THE SAFE COMPLETELY READ AND
UNDERSTAND THE MANUAL BEFORE SECURING
ITEMS IN THE SAFE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
NOTE: This safe is NOT fire proof.
NOTE: This safe has no cash rating.
Never lock your spare override keys or the in-
struction manual in the safe. Once the batter-
ies deplete, you will need to use the keys to
open the safe. Spare keys are unavailable!
Please make sure that after you have opened
the safe for the first time, you change the PIN,
for security reasons.
IDENTIFICATION
1. Locking knob
2. Ready green LED
3. Low battery red LED
4. Proceed orange LED
5. Concealed hinges
6. Electronic key pad
7. Lock cover
8. Security cap covering reset button
9. Battery cover
OPERATING THE SAFE FOR THE FIRST TIME
Use the Manual override key to open the safe.
f
Remove the plastic key lock cover (7).
f
Insert the override key; turn it anti-clockwise, at the
f
same time turn the locking knob (1) clockwise and
pull open the safe.
See BATTERY REPLACEMENT.
f
Keep the safe door open until you have set the PIN
f
code.
PROGRAMMING YOUR PIN NUMBER
(PERSONAL IDENTIFICATION NUMBER)
DEFAULT FACTORY PIN: 159
Each time a button (6) is pressed, a beep will be
f
heard and the Orange LED (4) will flash. This is a
safety feature so that you will know when the safe is
being accessed and cannot be switched off.
Keep PIN Codes in a safe place.
f
Do not use personal information like birthdays, tele-
f
phone numbers etc.
Write down your PIN codes so you do not forget it
f
(any combination of numbers from 3 to 8 digits).
1. With the door open, remove the security cap (8)
by unscrewing it.
2. Depress the red reset button (8) located at the
back of the door.
3. Two beeps will be heard and the Orange LED (4)
will light.
4. You now have 20 seconds to enter your PIN.
5. Key in your new PIN.
6. Press the "A" or "B" button once.
7. Two beeps will be heard and the Orange LED (4)
will go out.
8. You PIN has now been set.
9. Screw the security cap (8) back onto the red reset
button. Ensure you do this for security reasons.
While the door is open familiarise yourself with the
f
door opening procedure, and leave the door open
until you are satisfied that you fully understand the
opening and closing method. You can re-set the PIN
at any time by following the above procedure.
OPENING THE DOOR USING
YOUR PIN NUMBER
(PERSONAL IDENTIFICATION NUMBER)
Each time a button (6) is pressed, a beep will be
heard and the Orange LED (4) will flash.
1. Enter your PIN number.
2. Press the "A" or "B" button.
3. Two beeps will be heard and the Orange LED (4)
will flash.
4. The Green LED (2) will light to indicate that the
safe door can be opened.
5. You now have 5 seconds to open the door before
it will lock again.
6. Open the safe door by turning the knob (1) clock-
wise and pulling it open.
If the Red and Green LED lights simultaneously
when the correct PIN is entered, then the batter-
ies MUST be replaced immediately before clos-
ing the door as this indicates that the batteries
are too low.
If an incorrect PIN is entered, the safe will not open,
three warning beeps will be heard & the Orange LED
will flash and the Green LED won't light. Entering an
incorrect PIN three consecutive times will freeze
the locking mechanism and keypad for 20 seconds,
during which time you will not be able to access
the safe. After three more incorrect PIN attempts,
the locking mechanism and keypad will freeze for 5
MINUTES during which time you will not be able to
access the safe.
OPENING THE SAFE USING THE OVERRIDE
KEY
Use the Manual override key to open the safe.
1. Remove the plastic key lock cover (7).
2. Insert the override key; turn it anti-clockwise, at
the same time turn the locking knob (1) clockwise
and pull open the safe.

BATTERY REPLACEMENT

The digital safe uses four AA type batteries (sup-
plied).
1. Remove the battery cover (9) on the rear of the
door.
2. Push the catch in and pull out the cover.
3. Install the 4 x AA batteries supplied. Ensure cor-
rect polarity (10).
4. Replace the battery cover.
5. Keep the safe door open until you have set the
PIN code.