Publicité
Digital system
A functional Fleischmann digital system with multiMAUS
– A transformer or switching power supply unit (e.g. ROC0 10725, Fleischmann 681301)
GB
– A feeder track without capacitor (e.g. geoLINE 61190, ROCO LINE 42517, Fleischmann 9400, 22217 (N),
6430 H0)
Please pay attention to the following instructions before you start connecting components:
The warranty will be voided if you are using ROCO and/or Fleischmann components together with compo-
nents from other companies. In addition, there is a risk of damage or malfunction to or of your digital system.
Your warranty will also be void if you open the housing of the multiMAUS
Previous ROCO amplifiers model 10761 and 10764 cannot be used together with the multiMAUS
The multiMAUS
PRO
batteries of the same type (1.2 V each). Please note the following information:
• Always comply with the local rules and regulations concerning consumed batteries (return to dealer or
collection points, for example). Never dispose of any type of battery with common household waste or
throw batteries into a fire.
• Always use batteries from one manufacturer.
• The batteries must have the same charge status and the same capacity.
• Do not mix regular batteries with rechargeable batteries.
• Keep out of reach of children. Batteries are not toys!
How to link your multiMAUS
1. Open the battery compartment on the back of the multiMAUS
teries. Please make sure the polarity is correct. Use the screw to re-close the battery compartment.
2. Press the "Light /OK" key to switch the multiMAUS
Now select the language version by pressing the arrow keys. Press "Light/OK" again. The scrolling text
"PRESS BUTTON ON CENTRE FOR 3 SEC" is displayed.
3. After pressing the "Connect" key on the multiZENTRALE
light up first followed by all four LEDs in the manner of a running light. The display restarts and "LOCO 1"
with flashing STOP symbol is depicted. The yellow LED flashes on the multiZENTRALE
"STOP" key of the multiMAUS
or the continuously lit green LED below the wireless symbol on the multiZENTRALE
less connection between the multiMAUS
4. To switch the multiMAUS
If the multiMAUS
shuts itself off after approximately 10 minutes. This time can be changed in the menu functions.
A completely depicted wireless symbol in the display indicates an optimal connection. The better the
connection, the more bars are displayed.
If the wireless connection is very bad, only the antenna symbol is depicted. If this is the case, it is pos-
sible that the system will lose some of its functionality.
If the wireless connection fails completely between the multiZENTRALE
antenna symbol flashes. If this is the case, no locomotive information (direction symbol, F-keys) is
displayed. The voltage supply of the system is switched off after an adjustable time (s. section 3 of the
manual); the yellow LED then flashes on the multiZENTRALE
reestablished, press the "STOP" key to continue in drive mode.
4
is supplied with electricity by 3 AAA batteries (micro) each with 1.5 V or 3 rechargeable
with the multiZENTRALE
PRO
to activate drive mode. An antenna symbol in the upper right of the display
PRO
off, press the "Light /OK" key together with the "MENU" key.
PRO
is not used or the wireless connection is not active for some time, the multiMAUS
PRO
and multiZENTRALE
PRO
:
PRO
and insert standard or rechargeable bat-
PRO
on. All of the display symbols are depicted briefly.
PRO
for at least 3 seconds, the red and yellow LEDs
PRO
and multiZENTRALE
PRO
PRO
PRO
requires the following items:
PRO
(except battery compartment).
PRO
. Simply press the
PRO
indicate that the wire-
PRO
has been established correctly.
and the multiMAUS
PRO
. One the wireless connection has been
.
PRO
PRO
, the
PRO
Publicité
