BOMANN MWA 9481 CB Mode D'emploi page 26

There are two methods of fi lling with water.
1. Bucket/Bowl:
You can fi ll in the water through the open lid by means of a
bucket.
2. Hose:
• Together with the hose the connection (5) serves as a
method of fi lling. Please use the new hose supplied and
connect one end to the washing machine.
• You can connect the other funnel-shaped end of the
hose carefully to a water tap and fi ll in water in a cont-
rolled manner via the tap.
Under no circumstances should the maximum fi lling height be
exceeded.
Washing
The machine is only suitable for washing textiles up to the stated
fi lling quantity.
• Empty the pockets of the clothing that is to be washed.
• It is best to wash particularly high-quality or sensitive
clothing in a washing bag or white pillow cover.
• Laundry that is particularly soiled should be pre-washed
once.
Washing and Washing Powder
• Determine the washing temperature in accordance with the
care instructions attached to the garments to be washed.
However, you should not wash anything above 50°C.
NOTE:
Your washing machine does not have its own heating sys-
tem. You should therefore mix the water to the appropriate
temperature beforehand.
• Determine the length of washing in accordance with the care
instructions and the degree of soiling.
The following table is intended to help you determine the amount
of washing powder you require.
Washing Water
Quantity Quantity
1,2-1,5 kg approx. 13 l
1,0-1,2 kg approx. 10 l
Up to 1,0 kg approx. 7 l
Operation
Preparation
• Insert the drainage hose (7) into the device at the top of the
washing machine.
• Place the washing in the machine.
• Fill in the water and the washing powder. See also the
section on „Washing and Washing Powder".
• Close the lid.
26
05-MWA 9491 CB 26
All manuals and user guides at all-guides.com
Washing Washing
Powder Powder
Concentrate Consump-
Consumption tion
15 g 20 g
10 g 17 g
5 g 14 g
Electrical Connection
• Please ensure that the timer is turned to „0" (off).
• Connect the mains lead to a properly installed 230 V, 50 Hz
socket.
Washing
• Set the desired washing time by means of the timer.
Stopping Operation
• Wait until the clock automatically stops the washing process
or turn the timer back to the „0" position.
• Remove the plug from the socket.
• Take an appropriate vessel of an adequate size in order to
drain off the dirty washing water via the drainage hose. To
this purpose you should remove the drainage hose from the
device and place it in the selected vessel.
• You can now remove the washing or rinse it again if neces-
sary.
• Close the lid and insert the drainage hose.
Cleaning
• Remove the mains plug from the socket.
• In order not to damage the surfaces you should not use any
abrasive detergents or cleaning equipment that will scratch.
Washing Drum
• Clean the lint screen.
• We recommend cleaning the washing drum with clear water
after washing is fi nished.
• It is extremely advisable to do this after you have been was-
hing with starch or bleach in order that the following washing
is not affected by this.
• Any soiling of the washing drum can be removed with a
sponge or nylon brush.
Housing
• The housing can be wiped off with a slightly damp cloth. Do
not immerse the motor device into water!
• Dry all parts after cleaning with a dry cloth.
Storage
• Empty the washing drum completely.
• Close the lid.
Troubleshooting
• Machine is not working.
Remedy: Check the mains connections.
Check the setting of the timer.
• Machine does not wash.
Possible cause: There is too much washing in the machine.
Remedy: Reduce the amount of washing.
Possible cause: The washing wheel has become loose.
Remedy: Tighten the washing wheel again.
25.10.2006, 16:13:50 Uhr