Table Des Matières; Intended Use - DeWalt DWE74911 Traduction De La Notice D'instructions Originale

English
GENERAL SAFETY WARNINGS

WARNING: Read all safety warnings and all
instructions enclosed with the saw stand and the
power tool to be mounted. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
General Safety Instructions for Table
Saw Accessories

WARNING: To reduce the risk of personal injury:
Follow the mounting instructions carefully.
•
Fasten the saw to the stand securely as
instructed. Proper assembly is important to
prevent the risk of a collapse of the saw stand.
Ensure all stand fasteners are securely
•
fastened and that all stand mechanisms are
in proper working order before mounting or
operating the table saw. Proper assembly is
important to prevent the risk of a collapse of the
saw stand.
Attach the power tool securely to the saw
•
stand before using it. Sliding off of the power
tool on the saw stand can lead to loss of control.
DO NOT use the stand on uneven surfaces.
•
DO NOT use the stand with the legs folded
and stand sitting on the ground. The stand is
designed to be used on a flat, stable surface.
If the saw stand can slide around or wobbles, the
power tool or the workpiece cannot be evenly and
securely guided.
Pull the plug from the main receptacle and/
•
or remove the battery from the power tool
before making adjustments on the tool or
changing tool accessories. Unintentional
switching on of the power tool is the cause of
many accidents.
Ensure that long and heavy workpieces do
•
not affect to the balance of the saw stand.
Long and/or heavy workpieces must be supported
at the free end.
Keep your fingers clear of the hinge points
•
while folding the legs of the saw stand.
Danger of fingers being crushed or contused.
DO NOT modify or use stand for operations for
•
which it is unintended.
DO NOT use the stand on uneven surfaces. DO
•
NOT use the stand with the legs folded and stand
sitting on the ground. The stand is designed to be
used on a flat, stable surface.
2
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

This table saw stand is designed for use with these table
saws: DW745, DWE7480, DWE7485, DCS7485, DWE7490,
DWE7491 and DWE7499. When used with the DW745,
DWE7480, DWE7485 and DCS7485 table saws, the adaptor
brackets (not included with DWE7491RS) must be mounted
to the saw prior to placing the saw on the stand. Do not use
this stand with any other tool.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and before making any
adjustments or removing/installing attachments
or accessories. An accidental start-up can
cause injury.
Tools Required
Hex key and small wrench (supplied)
Socket or wrench set
Contents
Instruction manual
Stand, right side
Stand, left side
Wheels (2)
Rear axle
Kickstand assembly
Tube plugs (2)
Handle assembly
DWE7490/DWE7491/DWE7499 saw
mounting hardware:
M8x75 Pan head bolts (4)
M8 Lock nuts (4)
M8 Flat washers (4)
DW745/DWE7480/DWE7485/DCS7485 saw mounting
hardware (not included with DWE7491RS):
Adapter brackets (front and rear) (2)
M6 Pan head bolts (4)
M6 Flat washers (4)
M6 Lock nuts (4)
M8 Pan head bolts (4)
M8 Flat washers (4)
M8 Lock nuts (4)
Handle feet (2)
Carriage head bolts (2)
M6x12 pan bolts (2)
M8x40 hex head bolts (4)
M8x40 pan head bolts (4)
M8 lock nuts (12)
Flat washers (2)