Reverse Function - Taurus SAVOY Mode D'emploi

- Prepare the appliance according to the function
you wish to use:
USE:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Prepare the appliance with the accessory requi-
red according to the food to be prepared.
- Cut all foods into pieces (sinewless, boneless
and fatless meats is recommended, approxima-
te size: 20x20x60mm) so that they fit easily into
the hopper opening.
- Turn the appliance on, by selection position I on
both switch buttons.
- Feed food into the hopper plate using only the
food pusher to introduce it into the feeding tube.
ACCESSORIES:
CUTTING PLATES (I)
- These cutting plates allow mincing meat with a
coarser or finer texture depending on the size of
the holes of the disc.
- Press the fasten button, hold the head and
insert it into the inlet (when inserting please pay
attention the head must be slanted as per arrow
indicated on the top (Fig. 1) then move the head
anticlockwise so that the head is fastened tightly
(Fig. 2)
- Insert the endless screw through the outlet
mouth of the mincing head (fig. 3)
- Position the cutting blade in the endless screw
with the cutting edge pointing towards the end-
less screw (Fig. 4)
- Insert one of the three cutting plates in the
endless screw, fitting the outlets of the cutting
plate in the notches of the outlet mouth edge of
the mincing head (Fig. 5)
- Screw the fasten rim tightly in the outlet mouth
of the mincing head turning clockwise to fit the
endless screw, blade and cutting plate (Fig. 6)
- Position the tray at the top of the mincing head.
NOOZLE FOR FILLING SAUSAGES (L)
- Insert the mincing head into the motor body
securing with the clamp for the blade holder.
- Insert the endless screw through the outlet
mouth of the mincing head (fig. 3)
- Position the cutting blade in the endless screw
with the cutting edge pointing towards the end-
less screw (Fig. 4)
- Insert the cutting plate with largest holes in the
endless screw, fitting the outlets of the cutting
plate in the notches of the outlet mouth edge of
the mincing head (Fig. 5)
- Insert the nozzle for filling sausages via the
sealing ring (Fig. 7)
- Screw the fasten rim tightly in the outlet mouth
of the mincing head turning clockwise to fit the
endless screw, blade and nozzle (Fig. 6)
- Position the tray at the top of the mincing head.
ACCESSORY FOR KEBBE (M)
- Insert the mincing head into the motor body
securing with the clamp for the blade holder
(Fig. 1)
- Insert the endless screw through the outlet
mouth of the mincing head (fig. 3)
- Insert the accessory for base Kebbe in the
endless screw and position the other Kebbe
accessory on top, fitting the outlets in the edge
notches of the filling mouth (Fig. 8)
- Screw the fasten rim tightly turning clockwise
to fit the accessories for Kebbe in the endless
screw (Fig. 9)
- Position the tray at the top of the mincing head.

REVERSE FUNCTION:

- In case of jamming, switch off the appliance
pressing both switches to "R" position.
- Endless screw will be rotating in the opposite
direction, and the head will get empty.
- If it does not work, switch off the appliance and
clean it.
- Wait for one minute before and after the reverse
function.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Turn the appliance off, using the on/off switch.
Select "0" position.
- Unplug the appliance from the mains.
- Clean the appliance.
CLEANING
- Disconnect the appliance from the mains and
allow it to cool before undertaking any cleaning
task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT
IMMERSE IN WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.