Technical Characteristics - Ugolini INSTANT 20/2 Carnet D'instructions

INSTANT

1 TECHNICAL CHARACTERISTICS

Number of powder containers
Capacity of each container, approx.
Capacity of water tank, approx
Dimensions:
width
depth
height
Net weight, approx.
Gross weight, approx.
IMPORTANT
Electrical characteristics: read the data featured on the
data plate of each dispenser; this data plate is situated at
the bottom of the compartment of the water tank. The
serial number of the appliance (preceded by the symbol
#) is given on the same data plate.
Specifications are subject to change without notice.
2 INTRODUCTION
Read this instruction manual carefully to find out all the
characteristics of the dispenser.
As with all mechanical products, this dispenser also requires
cleaning and care. In addition, its correct operation may be
compromised by possible errors made by the operator during
the disassembly and cleaning operations. For this reason, it is
important that the disassembly, cleaning, sanitising and
reassembly procedures - being everyday tasks - are familiar,
without any room for error on the part of all the personnel
responsible for the dispenser.
3 INSTALLATION
1 Take the dispenser out of its packaging, which we
recommend you keep for future requirements.
2 Make sure that the dispenser has not been damaged during
transportation. If this is the case, immediately make a claim
with the forwarder.
3 Place the dispenser onto a counter designed to withstand
its weight, including when full.
4 Before making the electrical connection to the dispenser,
check that the supply mains matches the one specified on the
data plate. Connect the dispenser to a single-phase network,
using an earthed socket as set forth by the applicable
regulations in force. If the dispenser is supplied without a plug,
connect to the cable a plug that is compliant with the standards
in force in your country, has an earth pin or contacts, and is
suitable for currents of at least 10 A 250 V (for areas with
voltages of 220-230 V 50-60 Hz) or 20 A 250 V (for areas with
voltages of 100-115 V 50-60 Hz). Should you wish to make a
fixed connection to the network, connect the cable to a bipolar
wall switch with a minimum contact opening of 3 mm. Do not
INSTANT INSTANT
20/2 20/3
n 2 3
cc 1000 1000
cc 4500 4500
cm 19 27
cm 39 39
cm 52 52
kg 20 25
kg 22 27
10
use extensions for the electrical connection of the appliance.
ATTENTION
Make sure the appliance is earthed correctly; if this is not
the case, this may cause electric shocks to people or
damage to the dispenser.
5 The dispenser is not supplied pre-cleaned and sanitised by
the factory. Before use, it must be disassembled, cleaned and
sanitised according to the instructions provided herein (see
paragraph 6 CLEANING AND SANITIZING PROCEDURES).
IMPORTANT
Position the appliance in such a way that the power
supply cable plug is easily accessible.
4 TO OPERATE SAFELY
1 Do not use the dispenser before reading this instruction
manual first.
2 Do not use the dispenser unless it is earthed correctly.
3 Do not use extensions for the electrical connection of the
dispenser.
4 Do not operate the dispenser if the panels and the lids on
the electrical parts are not in place and secured with screws.
5 Do not insert your fingers or objects into the vents and
product outfeed orifice.
6 Connect the device to a system with a nominal voltage of
230V and a maximum impedance of Zmax = 0.34 Ω.
7 For best results, use only powders specially prepared for
freeze - dried produ cts an d foll ow the man ufactu r er' s
instructions.
5 OPERATING PROCEDURES
5. 1 PREPARING THE DISPENSER
1 Before use, clean and sanitise the dispenser according to
the instructions provided herein (see paragraph 6 CLEANING
AND SANITIZING PROCEDURES).