Lutron Serena CSPS-P1-1-6-WH Manuel D'installation

Serena RF Insulating Honeycomb Shade
®
1 2
Prepare to Install Mount Shade
2.1 Verify Correct Shade Size
Important Notes
Hold the shade up to the window to make sure it is the correct
Please Read Before Installing
size.
! WARNING: SHOCK HAZARD. Can cause serious
NOTE: For outside mounting, center the shade with the window
injury or death. Read and follow all instructions.
and mark the wall or trim at each end of the shade.
! CAUTION: RISK OF FALLING OBJECTS. Securely
install the shade system per the mounting instructions.
Failure to do so could result in minor or moderate
2.2 Attach Brackets to Mounting Surface
injury
• Use Bracket Placement Table below to position bracket on mounting surface and mark hole
1. Read, follow, and save these instructions.
locations for pre-drilling.
2. When mounting the brackets, make sure you are
• Use a level to make sure the marks are aligned.
screwing into wood studs if possible. If not, you
• Pre-drill holes for the screws. Repeat for all brackets.
must use appropriate fasteners (not included) for the
mounting surface.
• Install the mounting brackets using the provided screws or other appropriate fasteners.
3. Make sure the brackets are aligned with each other.
If not, the shade may not properly snap into the
Inside Mount
brackets.
4. Install the shade on its brackets and ensure a clear
path for its travel before installing batteries.
5. Keep all LTE Devices (routers, mobile phones, etc.)
at least 3 ft (1 m) away from shade.
Included Components Required Tools
• Shade • Pencil
• Mounting brackets • Tape measure
• Mounting screws • Drill with 3/32" drill bit
• Spacers, if applicable • #2 Phillips screwdriver
Power Source Options (sold separately)
window frame
• Batteries (type and quantity vary with shade width):
Eight (8) AA, lithium
or
Four (4) D, alkaline
Rechargeable
batteries
Six (6) D, alkaline
bracket
Eight (8) D, alkaline 1.25 in (32 mm)
minimum
• Individual Power Supply:
CSPS- P1-1-6-WH
2.3 Reposition Antenna Clip for Optimum Wireless Communication
NOTE: This step is not necessary for shades less than 21.75 in (654 mm) wide.
• 10 Output Power Supply Panel: • Unsnap the antenna clip from the headrail.
CSPS-P1-10-6
• Move it out to the operating position behind the headrail, and snap it into place.
CE Information
(For model numbers CS-EDU-YK-BULK and
CS-EDU-YQ-BULK)
Lutron Electronics hereby declares that CS-EDU-YK-BULK
and CS-EDU-YQ-BULK are in compliance with the
essential requirements and other relevant provisions of
2.4 Mount Shade in Brackets
Directive 1999/5/EC. A copy of the DoC can be obtained
Holding the shade in both hands, tilt the top of the shade slightly toward the window and hook
by writing to:
the front edge into the brackets behind the battery release tabs (
Lutron Electronics Co., Inc.
of the headrail up and press the bottom of the headrail firmly until you hear it click into place.
7200 Suter Road
IMPORTANT: Be certain no fabric cells are caught in the brackets.
Coopersburg, PA 18036 U.S.A.
TRA Compliance Information
(For model number CS-EDU-YK-BULK)
TRA
Registered No:
ER0096954/12
Worldwide Headquarters | USA
Dealer No: 0016561/08
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299 USA
TEL: 1.610.282.3800
FAX: 1.610.282.3090
Technical Support: 1.800.523.9466
Toll Free: 1.888.LUTRON1
EMAIL: shadinginfo@lutron.com
WEB: www.lutron.com/shadingsolutions
Bracket Placement / Colocación de soportes / Positionnement de support
Shade width / Anchura de la persiana / Largeur du store 14.5 in – 25.875 in (368 mm – 657 mm)
1 1
Top view of shade
Vista superior de la persiana
2 3 2
Vue du dessus du store www.lutron.com/honeycombmaintenance
Front view of shade
4 4
Vista frontal de la persiana
Vue du devant du store
Shade width / Anchura de la persiana / Largeur du store 26 in – 45 in (660 mm – 1143 mm)
1 1
Top view of shade
2 3 2
Vista superior de la persiana
Vue du dessus du store
2 in
(5 cm)
Shade width / Anchura de la persiana / Largeur du store 45.125 in – 72 in (1146 mm – 1829 mm)
1
Top view of shade
2 2
Vista superior de la persiana
Vue du dessus du store
2 in
(5 cm)
Shade width / Anchura de la persiana / Largeur du store 72.125 in – 96 in (1832 mm – 2438 mm)
1
Top view of shade
2
Vista superior de la persiana
Vue du dessus du store 2 in
(5 cm)
1/3 w
Troubleshooting
A Shade Does Not Respond
IMPORTANT: The shade is designed to respond when a control button is released. For best
response during normal operation, tap-and-release control buttons. Do not press and hold
unless instructed.
A-1 Tap the Shade Button. Does the Shade Button LED light up GREEN?
NO, Shade Button LED doesn't light up at all
Battery powered shade: 1) Make sure the batteries are installed in the correct
orientation. 2) Make sure batteries are fresh, or install new batteries.
Wired shade: 1) Make sure the power supply/panel is plugged in to a powered outlet.
2) Make sure the shade power cable is properly connected to the plug-in supply or
power panel, and system power is available.
NO, Shade Button LED is RED and/or blinking. See "Shade Button Blink Codes"
YES Continue to A-2 below...
A-2 Make sure the control is assigned to the shade by performing the steps in section
4.1: "Assign Controls" of the installation instructions.
Does the Shade Button LED blink GREEN while assigning controls?
NO, Shade Button LED does not respond to control input
1) See section 2.3: "Reposition Antenna Clip..." of the installation instructions.
2) Restore the shade's factory default settings. See the section: "Restoring Factory
Default" of the installation instructions.
NO, Shade Button LED is RED and/or blinking. See "Shade Button Blink Codes"
YES, Shade Button LED responds correctly, but shade still not moving
1) Repeat section 4.1: "Assign Controls" of the installation instructions, and be sure to
hold the "Close" button until the Shade Button LED blinks.
2) Reset the upper and lower limits. See sections 4.2: "Adjust Upper Limit" and
4.3: "Adjust Lower Limit" of the installation instructions.
Lutron Electronics Co., Inc.
02/2013
7200 Suter Road
P/N 045353 Rev. H
Coopersburg, PA 18036-1299, U.S.A.
Motorized shade with wireless radio frequency (RF) control
Installation Guide—Please Read Before Installing
3
3.1
Press ALL battery release tabs (
The shade will tilt forward.
3.2
Batteries
Install the batteries as indicated in the battery holders
(so the +/- signs match). Make sure the batteries are fully
inserted into the trays. The "shade button" will blink red/green
Outside Mount Outside Mount 3 times when shade is powered.
On Trim Above Trim*
NOTE: For best battery life, DO NOT mix old and new
batteries. Use ONLY alkaline D size batteries or lithium AA
size batteries. DO NOT install carbon-zinc or rechargeable
batteries, and DO NOT mix battery types.
OR
Uncoil the cable from inside the headrail and plug it into the
individual power supply. Plug the individual power supply into
an outlet. The "shade button" will blink red/green 3 times when
shade is powered.
* Hole locations should be no
less than 2.75 in (70 mm)
above the trim.
angled spacer* spacer
wall wall
OR
bracket bracket
10 Output Power Supply Panel
window window
For wiring instructions from a 10 output power supply, refer
trim trim
to the power panel instruction guide (P/N 045-348) that came
with the 10 output power supply panel.
* If window trim is angled, place an angled 2.75 in
spacer (not included) behind each bracket.
(70 mm)
Ensure that the trim is level before placing
minimum
3.3
the bracket flush against its edge Pre-drill a
hole through the spacer.
Tilt the shade back into the brackets; pressing gently until you
hear a click.
PUSH).Then rotate the back
LIMITED WARRANTY
Subject to the exclusions and restrictions described below, Lutron
warrants that each System will be free from manufacturing defects
end
bracket from the date of shipment by Lutron for a period of (a) one year as
cap
to the wall controls, interfaces and system accessories of the Shade
omitted
hook
System ("External Components") and (b) eight years as to the other
front for
Systems and the electronic drive unit, shade fabric and shade hardware
edge clarity
of the Shade System. If any manufacturing defect exists in the External
Components, so long as Customer promptly notifies Lutron of the defect
within the one year warranty period and, if requested by Lutron, returns
the defective part(s), Lutron will, at its option, either repair the defective
part(s) or provide comparable replacement part(s). If any manufacturing
defect exists in any of the components of a System other than the
External Components, so long as Customer promptly notifies Lutron
of the defect within the eight year warranty period and, if requested
by Lutron, returns the defective part(s), Lutron will, at its option, either
repair the defective part(s) or issue a credit to the Customer against
the purchase price of comparable replacement part(s) purchased from
Lutron as provided below:
• Up to 5 years from ship date: 100% of cost
Europe Headquarters | United Kingdom
• More than 5 but not more than 8: 50% of cost
Lutron EA Ltd • More than 8: 0% of cost
6 Sovereign Close Replacement parts for the System provided by Lutron or, at its sole
discretion, an approved vendor may be new, used, repaired, reconditioned,
London, E1W3JF, UK
and/or made by a different manufacturer.
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
EXCLUSIONS AND RESTRICTIONS
Technical Support: +44.(0)20.7680.4481 This Warranty will be void, and Lutron and its suppliers will have
FREEPHONE: 0800.282.107 no responsibility under this Warranty, if Lutron or its representatives
cannot access any components of the System to inspect, diagnose
problems with or repair the System or any of its components as a
result of concealment or inaccessibility of such components within
English
2
1 1. Bracket
2. Cord lift spool
3. Drive
Top view of shade and bracket
4. Yellow bracket label
2
Vista superior de la persiana y soporte
www.lutron.com/honeycombmaintenance
Vue du dessus du store et support
Español
1. Soporte
2. Bobina de cuerda de elevación
3. Motor
4. Etiqueta de persiana amarilla
Français
1. Support
2. Bobine de levage à corde
3. Conducteur
4. Étiquette de store jaune
2 in
(5 cm)
1 1
3 2
2 in 2 in
(5 cm) (5 cm)
1 1
2 3 2 2
1/3 w 1/3 w
B Wireless Control Range Is Too Short
B-1 See section 2.3: "Reposition Antenna Clip..." of the installation instructions.
C
Shade Is Not Level
C-1 Leave shade in lowered position to allow fabric to relax. Time required to relax may
vary (up to 24 hours).
D Shade Does Not Reach Window Sill
D-1 Reset the lower limit. See section 4.3: "Adjust Lower Limit" of the installation
instructions.
D-2 Leave shade in lowered position to allow fabric to relax. Time required to relax may
vary (up to 24 hours).
D-3 Check the window measurements, shade measurements, and the mounting height.
Shade Button Blink Codes
RED/GREEN RED/GREEN RED/GREEN Over a 3-second span indicates normal power-up
when batteries are inserted or power connected.
One RED blink every 5 seconds = low batteries. Install new batteries.
Solid RED during shade movement = low batteries. Install new batteries.
Restoring Factory Default
Tap the Shade Button quickly three times, and hold the Shade Button after the third tap until
the Shade Button LED blinks GREEN rapidly.
Immediately tap the Shade Button quickly three more times, until the Shade Button LED blinks
GREEN rapidly, then blinks RED/GREEN three times, and turns off.
If you have any questions regarding your Lutron Insulating Honeycomb Shades, please visit
www.lutron.com, or call Lutron Technical Support at 1.800.523.9466. Our technical support staff
is available 24 hours a day, 7 days a week.
4
Install Power Source Assign Control and Program Shade
Expose Top of Headrail Compatible Controls (sold separately)
Pico wireless control
®
PUSH) above the headrail.
Open
Raise
Shade button
Connect Power Source
Close
4.1 Assign Controls
• Tap the "shade button" on all of the shades you want to assign. The "shade button"
illuminates green while in programming mode.
NOTE: Programming mode will time out after 30 seconds of inactivity.
• Press and hold the "Close" button on the control for about 6 seconds, until the "shade
button" blinks and turns off—exiting programming mode.
4.2 Adjust Upper Limit (optional)
The upper limit is pre-programmed based on your window dimensions.
• Tap the "shade button" on the shade you want to adjust. The "shade button" illuminates
green while in programming mode.
NOTE: Programming mode will time out after 30 seconds of inactivity.
• Press and hold the "Open" and "Raise" buttons on the control simultaneously for about 5
seconds, until the "shade button" blinks and remains on.
• Use the control's "Raise" and "Lower" buttons to adjust shade position to the upper limit
you prefer.
NOTE: When raising the shades, do not compress the fabric too much. Cells should just
be gently closed.
• Press and hold "Open" button for about 5 seconds, until the shade button blinks and turns
off, indicating the upper limit is set.
NOTE: For Pico wireless control's with an LED, simultaneously press and hold "Open" and
"Raise" until the LED on the Pico turns off—exiting programming mode.
Return Shade to Operating Position
4.3 Adjust Lower Limit (optional)
The lower limit is pre-programmed based on your window dimensions.
• Tap the "shade button" on the shade you want to adjust. The "shade button" illuminates
green while in programming mode.
e e
NOTE: Programming mode will time out after 30 seconds of inactivity.
• Press and hold the "Open" and "Raise" buttons on the control simultaneously for about 5
seconds, until the "shade button" blinks and remains on.
• Use the control's "Raise" and "Lower" buttons to adjust shade position to the lower limit
you prefer.
Removing the Shade from the Brackets
Bracket
(front view,
• Each bracket includes a release tab at the bottom-center. When
no shade)
pushed, the bracket releases the back of the headrail.
• With the shade fully raised, support it with one hand while using a
finger of the other hand to press the release tab. Repeat for each
bracket on the shade.
• Once shade is released from all brackets you can lift the shade off the
brackets.
Release Tab
a building structure.
This Warranty does not cover, and Lutron and its suppliers are
not responsible for:
1. Damage, malfunction or inoperability diagnosed by Lutron or a
Lutron approved third party as caused by normal wear and tear,
abuse, misuse, incorrect installation, neglect, accident, interference
or environmental factors, such as (a) use of incorrect line voltages
fuses or circuit breakers; (b) failure to install, maintain and operate the
System pursuant to the operating instructions provided by Lutron and
the applicable provisions of the National Electrical Code and of the
Safety Standards of Underwriter's Laboratories; (c) use of incompatible
devices or accessories; (d) improper or insufficient ventilation; (e)
unauthorized repairs or adjustments or alterations; (f) vandalism; (g)
an act of God, such as fire, lightning, flooding, tornado, earthquake,
hurricane or other problems beyond Lutron's control; or (h) direct
exposure to corrosive materials.
2. On-site labor costs to diagnose issues with, and remove, repair, replace,
adjust, reinstall and/or reprogram the System or any of its components.
3. Components and equipment external to the System, such as,
non-Lutron lighting and automation systems; building wiring audio-
visual equipment; and non-Lutron time clocks, photosensors and
motion detectors.
4. The cost of repairing or replacing other property that is damaged
when any System does not work properly, even if the damage was
caused by the System.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO EIGHT YEARS
FROM THE DATE OF SHIPMENT, EXCEPT THAT SUCH IMPLIED
Solución de problemas
A
La persiana no responde
IMPORTANTE: La persiana está diseñada para responder cuando sea liberado un botón de control.
Para una mejor respuesta durante la operación normal, toque y suelte los botones de control. No
pulse y mantenga pulsado a menos que así se le indique.
A-1 Toque el Botón Persiana. ¿Se ilumina de VERDE el LED del Botón Persiana?
NO, el LED del Botón Persiana no se enciende en absoluto
Persiana operada a baterías: 1) Asegúrese de que las baterías estén instaladas en
la orientación correcta. 2) Asegúrese que las baterías tengan carga o instale baterías
nuevas.
Persiana cableada: 1) Asegúrese de que la fuente de alimentación o el panel estén
enchufados a un tomacorriente energizado. 2) Asegúrese de que el cable de
alimentación eléctrica de la persiana esté correctamente conectado al tomacorriente o
el panel de alimentación eléctrica, y de que haya suministro eléctrico disponible para el
sistema.
NO, el LED del Botón Persiana se ilumina de ROJO y/o destella. Consulte "Códigos de
destello del Botón Persiana"
SÍ Continúe a A-2 presente a continuación ...
A-2 Asegúrese de que el control esté asignado a la persiana llevando a cabo los pasos de la sección
4.1: "Asignación de controles" de las instrucciones de instalación.
¿Destella de color VERDE el LED del Botón Persiana mientras se asignan los controles?
NO, el LED del Botón Persiana no responde a la entrada de control
1) Consulte la sección 2.3: "Reposicionamiento del clip de antena ..." de las instrucciones
de instalación.
2) Restaure la configuración de fábrica de la persiana. Consulte la sección: "Restauración
de los valores predeterminados de fábrica" de las instrucciones de instalación.
NO, el LED del Botón Persiana se ilumina de ROJO y/o destella. Consulte "Códigos de
destello del Botón Persiana"
SÍ, el LED del Botón Persiana responde correctamente, pero la persiana aún no se mueve
1) Repita la sección 4.1: "Asignación de controles" de las instrucciones de instalación y
asegúrese de mantener pulsado el botón "Cerrar" hasta que el LED del Botón Persiana
destelle.
2) Reinicialice los límites superior e inferior. Consulte las secciones 4.2: "Ajuste del límite
superior" y 4.3: "Ajuste del límite inferior" de las instrucciones de instalación.
1 NOTA: Si la persiana responde al asignarle controles o establecer los límites superior e inferior, pero no
responde luego, espere al menos 5 minutos y luego vuelva a intentar la operación normal.
Dépannage
2 in
(5 cm)
A Le store ne répond pas
IMPORTANT : Le store est conçu pour répondre lorsqu'on relâche le bouton de commande. Pour
une réponse optimale durant le fonctionnement normal, appuyez et relâchez de suite les boutons de
commande. Ne maintenez pas la pression sauf indication.
English
A-1 Appuyez sur le Bouton du Store. Est-ce que la LED du Bouton du Store s'allume en VERT?
NON, la LED du Bouton du Store ne s'allume pas du tout
Store alimenté par piles : 1) Assurez-vous que les piles sont installées dans le bon sens.
2) Assurez-vous que les piles sont en bon état, ou installez des piles neuves.
Store câblé : 1) Assurez-vous que l'alimentation/le panneau d'alimentation sont
branchés sur une prise sous tension. 2) Assurez-vous que le câble d'alimentation du
store est connecté correctement à l'alimentation ou au panneau d'alimentation, et que
l'alimentation du système est disponible.
NON, la LED du Bouton du Store est ROUGE et/ou clignote. Voir « Codes de clignotement du
Bouton du Store »
OUI Continuez avec A-2 ci-dessous...
A-2 Assurez-vous que la commande est attribuée au store en effectuant les étapes de la section
4.1 : « Attribuer les commandes » des instructions d'installation.
Est-ce que la LED du Bouton du Store clignote en VERT pendant l'attribution des
commandes ?
NON, la LED du Bouton du Store ne répond pas à l'entrée de commande
1) Voir la section 2.3 : « Repositionner le support de l'antenne... » pour les instructions
d'installation.
2) Restaurer les réglages d'usine du store. Voir la section : « Restaurer les réglages d'usine »
des instructions d'installation.
NON, la LED du Bouton du Store est RED et/ou clignote. Voir « Codes de clignotement du
Bouton du Store »
OUI, la LED du Bouton du Store répond correctement, mais le store ne bouge toujours pas.
1) Recommencez la section 4.1 : « Attribuer les commandes » des instructions d'installation,
et veillez à appuyer et maintenir le bouton « Fermer » jusqu'à ce que la LED du Bouton du
Store clignote.
2) Restaurer les limites inférieures et supérieures. Voir la section 4.2 : « Régler la limite
supérieure » et 4.3 : « Régler la limite inférieure » des instructions d'installation.
REMARQUE : Si le store répond pendant l'attribution des commandes ou le réglage des limites
inférieures et supérieures, mais ne répond plus ensuite, attendez au moins 5 minutes puis
réessayez le fonctionnement normal.
Shade button
(Clear plastic button above headrail)
Shade
Open
Preset
Lower
Close
4.3
• Press and hold "Close" button for about 5 seconds, until the shade button blinks and turns
off, indicating the lower limit is set.
NOTE: For Pico wireless control's with an LED, simultaneously press and hold "Open" and
"Raise" until the LED on the Pico turns off—exiting programming mode.
4.4
The preset level is pre-programmed to 50% open/closed.
• A. Use the control's "Raise" and "Lower" buttons to adjust shade position to the level you
prefer.
• B. Press and hold the "Preset" button on the control for about 5 seconds, until the "shade
button" blinks and turns off.
4.5
• Repeat step 4.4:A for one shade at a time;
disconnecting the power source from all
other shades while the preset level is set.
• When all preset levels are set, restore power
to all shades and perform step 4.4:B to set
the preset levels.
Restoring Factory Default
• This step will remove any controls assigned to the shade. It will not affect the shade's
upper and lower limits.
• Tap the Shade Button quickly three times, and hold the Shade Button after the third
tap until the Shade Button LED blinks GREEN rapidly.
• Immediately tap the Shade Button quickly three more times, until the Shade Button
LED blinks GREEN rapidly, then blinks RED/GREEN three times, and turns off.
Cleaning the Fabric
Press
release tab
To keep your shades looking their best, regularly brush them with a feather duster or lightly vacuum them
(side view)
with a clean brush-type attachment.
If your shades get a spot of dirt or a stain on them use a clean, soft cloth and a solutions of mild detergent
and warm water (1 part detergent to 3 parts water) to blot or lightly rub the spot or stain.
DO NOT use strong detergents or spot removers, and DO NOT have your shades dry cleaned.
IMPORTANT: Be extra careful if you are cleaning a room darkening fabric because you could permanently
crease the fabric.
WARRANTIES ARE LIMITED TO ONE YEAR FROM THE DATE OF PARTIES UNDER THIS WARRANTY ON ANY CLAIM FOR DAMAGES
SHIPMENT AS TO THE EXTERNAL COMPONENTS. ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE,
SALE, INSTALLATION, DELIVERY, USE, REPAIR, OR REPLACEMENT
NO LUTRON AGENT, EMPLOYEE OR REPRESENTATIVE HAS
OF THE SYSTEM, AND CUSTOMER'S SOLE REMEDY FOR THE
ANY AUTHORITY TO BIND LUTRON TO ANY AFFIRMATION,
FOREGOING, WILL BE LIMITED TO THE AMOUNT PAID BY
REPRESENTATION OR WARRANTY CONCERNING THE SYSTEMS.
CUSTOMER FOR THE SYSTEM. THE FOREGOING LIMITATIONS,
UNLESS AN AFFIRMATION, REPRESENTATION OR WARRANTY
EXCLUSIONS AND DISCLAIMERS WILL APPLY TO THE MAXIMUM
MADE BY AN AGENT, EMPLOYEE OR REPRESENTATIVE IS
EXTENT ALLOWED BY APPLICABLE LAW, EVEN IF ANY REMEDY
SPECIFICALLY INCLUDED HEREIN, OR IN STANDARD PRINTED
FAILS ITS ESSENTIAL PURPOSE.
MATERIALS PROVIDED BY LUTRON, IT DOES NOT FORM A
PART OF THE BASIS OF ANY BARGAIN BETWEEN LUTRON AND THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY
CUSTOMER AND WILL NOT IN ANY WAY BE ENFORCEABLE ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
BY CUSTOMER. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION
IN NO EVENT WILL LUTRON OR ANY OTHER PARTY BE LIABLE
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
FOR EXEMPLARY, CONSEQUENTIAL, INCIDENTAL OR SPECIAL
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
DAMAGES (INCLUDING, BUT NOT LIMITED TO DAMAGES FOR
PERSONAL INJURY, FAILURE TO MEET ANY DUTY, INCLUDING
OF GOOD FAITH OR REASONABLE CARE, NEGLIGENCE, OR
ANY OTHER LOSS WHATSOEVER), NOR FOR ANY REPAIR
WORK UNDERTAKEN WITHOUT LUTRON'S PRIOR WRITTEN
CONSENT ARISING OUT OF OR IN ANY WAY RELATED TO THE
INSTALLATION, DEINSTALLATION, USE OF OR INABILITY TO USE
THE SYSTEM OR OTHERWISE UNDER OR IN CONNECTION WITH
ANY PROVISION OF THIS WARRANTY, EVEN IN THE EVENT OF
THE FAULT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY,
BREACH OF CONTRACT OR BREACH OF WARRANTY OF LUTRON
OR ANY OTHER PARTY, AND EVEN IF LUTRON OR SUCH OTHER
PARTY WAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER MIGHT
INCUR FOR ANY REASON WHATSOEVER (INCLUDING, WITHOUT
Lutron, O, Sivoia, Pico, RadioRA, Homeworks, seeTouch, and GRAFIK
LIMITATION, ALL DIRECT DAMAGES AND ALL DAMAGES LISTED
Eye are registered trademarks of Lutron Electronics Co., Inc.
ABOVE), THE ENTIRE LIABILITY OF LUTRON AND OF ALL OTHER
B
El rango de control inalámbrico es demasiado reducido
B-1 Consulte la sección 2.3: "Reposicionamiento del clip de antena ..." de las
instrucciones de instalación.
C
La persiana no está nivelada
C-1 Deje la persiana en la posición inferior para permitir que la tela se distienda. El tiempo
de distensión podría variar (hasta 24 horas).
D La persiana no llega al alféizar de la ventana
D-1 Reinicialice el límite bajo. Consulte la sección 4.3: "Ajuste del límite inferior" de las
instrucciones de instalación.
D-2 Deje la persiana en la posición inferior para permitir que la tela se distienda. El tiempo
de distensión podría variar (hasta 24 horas).
D-3 Verifique las medidas de la ventana, las medidas de la persiana y la altura del montaje.
Códigos de destello del Botón Persiana
ROJO/VERDE ROJO/VERDE ROJO/VERDE durante un lapso de 3 segundos indica un
encendido normal cuando se insertan las baterías o se conecta el suministro eléctrico.
Un destello del LED ROJO cada 5 segundos = baterías bajas. Instale baterías nuevas.
Iluminación continua del LED ROJO durante el desplazamiento de la persiana = baterías bajas.
Instale baterías nuevas.
Restauración de los valores predeterminados de fábrica
Pulse el Botón Persiana rápidamente tres veces, y manténgalo presionado luego de la tercera
pulsación hasta que el LED del mismo destelle rápidamente de VERDE.
Toque inmediatamente el Botón Persiana rápidamente tres veces más, hasta que el LED del
Botón Persiana destelle rápidamente de VERDE, luego destelle tres veces de ROJO/VERDE y
se apague.
Si tuviera alguna pregunta con respecto a sus persianas aisladoras celulares de Lutron, visite
www.lutron.com, o comuníquese con la Asistencia Técnica de Lutron en el +1.610.282.6701.
Nuestro personal de asistencia técnica se encuentra disponible las 24 horas del día, los 7 días de
la semana.
B La portée de la commande sans fil est trop courte
B-1 Voir la section 2.3 : « Repositionner le support de l'antenne... » pour les instructions
d'installation.
C Le store n'est pas lisse
C-1 Laissez le store en position basse pour permettre au tissu de se détendre. Le temps
de détente nécessaire peut varier (jusqu'à 24 heures).
D
Le store n'atteint pas le rebord de la fenêtre
D-1 Réinitialisez la limite inférieure. Voir la section 4.3 : « Régler la limite inférieure » des
instructions d'installation.
D-2 Laissez le store en position basse pour permettre au tissu de se détendre. Le temps
de détente nécessaire peut varier (jusqu'à 24 heures).
D-3 Vérifiez les dimensions de la fenêtre, les dimensions du store et la hauteur de
montage.
Codes de clignotement du Bouton du Store
ROUGE/VERT ROUGE/VERT ROUGE/VERT pendant une durée de 3 secondes indique une
mise sous tension normale lorsque les piles sont insérées ou que l'alimentation est connectée.
Un clignotement ROUGE toutes les 5 secondes = piles déchargées. Installez de nouvelles
piles.
Voyant ROUGE pendant le mouvement du store = piles déchargées. Installez de nouvelles
piles.
Restaurer les réglages d'usine
Appuyez trois fois rapidement sur le Bouton du Store, et maintenez le Bouton du Store après la
troisième pression jusqu'à ce que la LED du Bouton du Store clignote rapidement en VERT.
Appuyez immédiatement trois fois de nouveau sur le Bouton du Store, jusqu'à ce que la LED du
Bouton du Store clignote rapidement en VERT, puis clignote en ROUGE/VERT et s'éteigne.
Si vous avez des questions concernant vos stores plissés en nid d'abeille isolants Lutron, veuillez
consulter www.lutron.com, ou appelez l'assistance technique de Lutron au 1.800.523.9466. Notre
personnel d'assistance technique est disponible 24 heures sur 24, 7 jours sur 7.
English
Adjust Lower Limit (optional)—continued
Set Preset Levels (optional)
Set Preset on Multiple Shades to Different Levels (optional)
FCC Information
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio and television
reception, which can be determined by turning the equipment off and on.
The user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron
Electronics Co. could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation. This Class B digital apparatus complies with
Canadian ICES-003.
IC Information
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject tot he following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation of the device.
Español
Français