Publicité
Les langues disponibles
Les langues disponibles
Release all air from filter and piping system.
In a flooded suction system (water source higher than pump), pump will prime itself when suction and
discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only .Pump should prime now. Priming time will depend on vertical
length of suction lift and horizontal length of suction piping.
1. Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal,
always depress handle before turning.)
3. Prime and start pump. Never tun pump dry! Running pump dry may damage seals,causing leakage and flooding!
Fill pump with water before starting motor. (be sure all suction and return lines are open), allowing the filter tank
to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial
back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about
1/2 to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation in the
filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher than the
initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control
valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
3
2
2
1
17
INSTALL/START-UP OF FILTRATION
REPLACEMENT PARTS OF FILTER
6
4
5
13
14
15
16
Item No. Part No.
01013051 32mm & 38mm Adaptor
1
2
02020013 O- Ring
3
88281105 4 Way Valve
4
01013047 Hose adaptor
5
02011026 Sleeve for Hose
6
01013046 Nut for Hose
7
7
01370011 Hose
8
01013049 Hose adaptor with nut
6
9
02011104 O- Ring
5
88028319 AMU012TP AQUA-MINI Pump(with timer & pre-filter)
8
88027719 AMU012P AQUA- MINI Pump(with pre- filter)
9
10
88028320 AMU016TP AQUA-MINI Pump(with timer & pre-filter)
10
2
88027720 AMU016P AQUA- MINI Pump(with pre- filter)
1
88028301 AMU020TP AQUA-MINI Pump(with timer & pre-filter)
88027701 AMU020P AQUA- MINI Pump(with pre- filter)
11
89033601 Pump Assembly Screw
11
12
01111105 Combo Base
12
06021014 Plastic Pressure Gauge With O-Ring (28psi)
13
89033602 Clamp Lock with Screws & Nut
14
15
02010045 O- Ring
11
16
01331061 13" Filter Tank
17
89033603 Lateral Assembly with Center Pipe
2-4
Product Description
Qty
3
4
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Publicité
