Defort DCD-18Nx2DF Mode D'emploi page 2

9
- if liquid comes into contact with the skin, wash quickly with
English
soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, ß ush eyes with clean water for
a minimum of 10 minutes and seek immediately medical
Cordless drill/driver
attention
• When battery is not in tool or charger, it should be kept away
from metal objects such as nails, screws, keys etc. to prevent
INTENDED USE
short-circuit
• This tool is intended for drilling in wood, metal, ceramic and
• Do not use charger when damaged; take it to one of the
plastic; tools with electronic speed control and left/right rotation
ofÞ cially registered SBM Group Service Stations for a safety
are also suitable for screwdriving and thread cutting
check
• Do not use battery when damaged; it should be replaced
TECHNICAL SPECIFICATIONS 1
immediately
• Do not disassemble charger or battery
PRODUCT ELEMENTS 2 • Do not attempt to recharge non-rechargeable batteries with the
charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
1 Switch for on/off and speed control
• Do not connect the blue (= neutral) or brown (= live) wire in the
2 Switch for changing direction of rotation
cord of the charger to the earth terminal of the plug
3 Keyless chuck
• If for any reason the old plug is cut off the cord of the charger,
4 Ring for torque control
it must be disposed of safely and not left unattended
5 Switch for selecting mechanical speed
To ensure longer service life and proper performance
SAFETY
of the battery, take the following actions when you
WARNING! Read all instructions. Failure to follow all instructions
start using new battery:
listed below may result in electric shock, Þ re and/or serious in-
jury. 1. Use the new battery, without recharging it, till its complete
discharge.
• Ensure the switch is in the off position before inserting battery 2. Then charge the battery for 3-5 hours.
pack. Inserting the battery pack into power tools that have the 3. Repeat abovementioned actions (1 and 2) 3-5 times to reach
switch on invites accidents. the nominal battery capacity.
• Recharge only with the charger speciÞ ed by the manufacturer.
A charger that is suitable for one type of battery pack may
MAINTENANCE
create a risk of Þ re when used with another battery pack.
• Use power tools only with speciÞ cally designated battery Make sure that the machine is not live when carry-
packs. Use of any other battery packs may create a risk of
ing out maintenance work on the motor.
injury and Þ re.
• Avoid damage that can be caused by screws, nails and other
Regularly clean the machine housing with a soft cloth, preferably
elements in your workpiece; remove them before you start
working after each use. Keep the ventilation slots free from dust and dirt.
• Always check that the supply voltage is the same as the If the dirt does not come off use a soft cloth moistened with soapy
voltage indicated on the nameplate of the charger (chargers water. Never use solvents such as petrol, alcohol, ammonia wa-
with a rating of 230V or 240V can also be connected to a 220V
ter, etc. These solvents may damage the plastic parts.
supply)
The machine requires no additional lubrication.
• In case of electrical or mechanical malfunction, immediately
Should a fault occur, e.g. after wear of a part, please contact your
switch off the tool or unplug charger from power source
local SBM Group dealer.
• SBM Group can assure ß awless functioning of the tool only
when original accessories are used
ENVIRONMENT
• Use only accessories with an allowable speed matching at
In order to prevent the machine from damage during transport,
least the highest no-load speed of the tool
it is delivered in a sturdy packaging. Most of the packaging ma-
• This tool should not be used by people under the age of 16
terials can be recycled. Take these materials to the appropriate
years
• Be careful not to drill or drive into areas where electrical wires recycling locations. Take your unwanted machines to your local
may be contacted SBM Group dealer. Here they will be disposed of in an environ-
• Ensure that switch (2) is in the middle (locking) position before mentally safe way.
making any adjustments or changing accessories as well as
NiCd batteries can be recycled. Deliver them to a disposal site for
when carrying or storing the tool
chemical waste so that they can be recycled or disposed of in an
• Do not touch the contacts in the charger
environmentally friendly manner.
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where temperature will
not exceed 40° C or drop below 0° C
• Batteries will explode in Þ re, so do not burn battery for any
reason
• When damaged, and under extreme usage and temperature
conditions, batteries may start to leak
6