RocHobby Mogrich Manuel D'utilisation page 10

Spare parts list
C2063
1:18 SHOCK PLASTIC PARTS
C2142
Classic Style Wheels plastic parts
C2143
Mud Tire
C2076
1:18 Gear Box Plastic Parts
C2075
1:18 FRONT OUTDRIVE SHAFT
C2069
1:18 SERVO HORN
C2066
1:18 BALL HEAD
C2067
1:18 Steering Hub & Spindle
C2068
1:18 FRONT/REAR AXLE parts
C2074
1:18 Rear Wheel Shaft
C2071
1:18 Wheel Hex
C2021
1:18 1KG High Torque 3wire Servo
C2049
1:18 050 Motor set
C2057
1:18 Plastic Gear set
C2058
1:18 Transmission Shaft full set
C2144
11810 Connecting Rod
C2145
11810 Rearview Mirror And Wiper
C2146
11810 Window
CE Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers
must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.
Appendix 1 FCC Statement
FCC ID: 2AUBX-HT-TX02
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or televison reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user authority to operate the equipment.
1. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-lacated or operating in conjunction with any other transmitter.End-users
and installers must be provided with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
2. Move all your channels to the desired position.
3. Select [All channels] and then [Yes] in the confirmation box.
C2147
11810 Car body
C2148
MINI HINGE
C2149
11810 Snokle and handel
C2150
11810 Hood
C2151
11810 Ligh Cup Set
C2152
11810 Lens
C2153
11810 Dash board SET
C2154
11810 Fender
C2155
11810 Seat
C2156
11810 Car hopper
C2051
ROCHOBBY USB Charger
C2157
11810 Light set
C2139
ROCHOBBY 1:18 Receiver
C2138
ROCHOBBY HT-TX02 Transmitter
C2137
ROCHOBBY HT-TX02 Transmitter Receiver Set
8
EN