Avertissements Et Mises En Garde - CYBEX Eagle Lat Raise Manuel D'utilisation

Avertissements et mises en garde

Les autocollants d'avertissement indiquent une situation potentiellement dangereuse qui peut entraîner des blessures
graves, voire mortelles si les mesures de sécurité ne sont pas respectées.
Les autocollants de mise en garde signalent une situation potentiellement dangereuse qui, si elle n'est pas évitée, risque
d'entraîner des blessures mineures ou moyennement graves.
Les schémas figurant après les autocollants indiquent l'emplacement de chaque autocollant.
R .19
4 PLACES
SAFETY YELLOW PMS 108
BACKGROUND. BLACK TRIANGLE
W/ YELLOW EXCLAMATION POINT,
BLACK LETTERS 18 PT ARIAL BOLD
TEXT.
INSET .06
WHITE
WHITE BACKGROUND WITH
BLACK 10 PT ARIAL BOLD TEXT.
R .19
PART NUMBER
4 PLACES
MATERIAL:
6 PT ARIAL BOLD
SAFETY YELLOW MUNSELL 5Y8/12
THIS NOTE REFERS TO ALL PLASTIC PARTS
BACKGROUND. BLACK TRIANGLE
AND ASSEMBLIES CONTAINING PLASTICS.
W/ YELLOW EXCLAMATION POINT,
RAW MATERIAL AND COMPONENTS ON
BLACK LETTERS 21 PT ARIAL
SUB-ASSEMBLIES AND ASSEMBLIES MUST
BOLD FONT
COMPLY WITH EUROPEAN DIRECTIVE
RoHS 2002/95/EC.
FINISH:
MATERIAL:
NOTE: See Engineering Drawing 4605-381-X for specifications.
ALL MATERIAL MUST COMPLY TO
EUROPEAN UNION DIRECTIVE
Manuel d'utilisation de la Cybex
DIMENSIONS
IN INCHES
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
MATERIAL:
ALL MATERIAL MUST COMPLY TO
EUROPEAN UNION DIRECTIVE
2002/95/EC RoHS (RESTRICTION
OF HAZARDOUS SUBSTANCES)
A
B
C
EXCEPT AS NOTED
E
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
GENERAL
MACHINING
EXCEPT AS NOTED
DIMENSIONS
DIMENSIONS
IN INCHES
IN INCHES
GENERAL
GENERAL
5
TOLERANCES:
TOLERANCES:
2 DECIMALS ± .03
2 DECIMALS ± .03
3 DECIMALS ± .015
TITLE:
CAUTION DECAL FRENC
DWG. BY
RH
CHECKED BY
125
SIZE SCALE
1:1
B
MATERIAL:
EXCEPT AS NOTED
REMOVE ALL BURRS
REMOVE ALL BURRS
BREAK SHARP EDGES
BREAK SHARP EDGES
ALL MATERIAL MUST COMPLY TO
.005/.010 R
.005/.010 R EUROPEAN UNION DIRECTIVE
2002/95/EC RoHS (RESTRICTION
SURFACE FINISH
SURFACE FINISH OF HAZARDOUS SUBSTANCES)
INDICATED PER
INDICATED PER
FINISH:
ANSI B46.1-1985
ANSI B46.1-1985
D
DATE TECH. PUBS. APPR.
DATE MFG. APPR.
SHEET DWG. NO.
4000Y316-2
1 1
OF
DIMENSI
IN INCHE
GENERA
TOLERAN
2 DECIM
TITLE:
3 DECIMA
TITLE:
CAUTION ANGLES
DECAL, CAUTIO
FEATURE
PERPEN
DWG. BY
DWG. BY DATE
OW
D
D
DATE