Rupes BA215S Сonversion Des Instructions De Fonctionnement Original page 9

TECHNICAL DATA
TYPE
INSULATION CLASS
ABSORBED POWER W
n NOMINAL RPM /min
Ø WHEEL DIAMETER mm
WHEEL SPINDLE THREAD
WHEEL SPINDLE STOP
WEIGHT Kg according to EPTA-Procedure 01/2003
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary.
Refer to the label technical specifications to the nominal values of the tool.
GENERAL WARNINGS
All instructions concerning safety and the prevention of industrial accidents
can be found in file SAFETY INSTRUCTIONS, that forms integral part of this
documentation. This INSTRUCTION MANUAL only contains additional
information that specifically explain how to use the machine.
SPECIFIC USE
General safety instructions
This electrical tool is designed to operate as a grinder, grinding and
abrasive cutting operations, metal brushing. Read all safety warnings,
instructions, illustrations and specifications supplied with this electrical
tool. Failure to respect all instructions shown below may cause electric shock,
fire and/or serious accident.
Sanding and polishing operations are not recommended with this electrical
tool. Operations for which the use of the electrical tool is not provided for can
create hazards and cause harm to personnel.
Theuse of this tool for smoothing, metal brushing and polishing operations
is not recommended. Its use for applications other than those for which it has
been designed may lead to hazardous situations and cause injuries to people.
Do not use accessories that are not specifically designed for the intended
use of the tool or that have not been recommended by the manufacturer.
The fact that an accessory can be fixed to the tool does not imply that it can be
used safely.
The rated speed of accessories must be at least equivalent to the maximum
speed of the tool. If operated at a greater speed than the rated one,
accessories may break and cause the ejection of chips.
The external diameter and thickness of accessories must be appropriate to
guarantee the protection and safety of the tool. Accessories with incorrect
dimensions cannot be adequately protected or controlled.
The configuration of the cutting/grinding wheels or any other accessory
mustperfectly adapt to the tool spindle. Accessories with holes that cannot be
BA215S
/ II
950
10.000
115
M14
YES
2,0
aligned with the fitting components on the tools will cause unbalance, excessive
vibrations and may be difficult to control.
Do not use an accessory if damaged. Before use, inspect all the accessories,
like the abrasive cutting/grinding wheels, in order to verify that they are not
cracked or splintered. If the tool or accessory has fallen, verify that they are
not damaged and, if necessary, replace it with a new one. After inspecting
or installing an accessory, move to a safe distance with any other person
present and operate the tool at maximum speed without load for one minute.
Damaged accessories generally break during this test period.
Wear personal protective equipment. According to the the application, use
face shield, mask or safety goggles. According to the case, wear a dust
mask, ear protection, gloves and a smock capable of stopping small abrasive
fragments of the work piece. Eye protection must be able to stop flying bits
produced from the different operations The dust mask or the respirator must be
capable of filtering particles produced by your work. Prolonged exposure to high
intensity noise can cause a loss of hearing.
Keep the people present at a safety distance with respect to the work area.
Anyone entering the work area must wear personal protection equipment.
The fragments of the work piece or the broken accessories can fly off and cause
injuries in the immediate vicinity of the work area.
Keep the tool only for isolating gripping surfaces, while the operations are
carried out in which the cutting accessory may be in contact with the hidden
cables or with its cable. The contact between the cutting accessory and the
cable "under voltage" can also put the exposed metal parts of the electrical tool
"under voltage" and can cause an electrical shock for the operator.
Position the cable far from the rotation accessory. If control is lost, the cable
can be cut or twisted and your hand or arm could be pulled into the rotation
accessory.
Never put the electrical tool back before the accessory has completely
stopped. The rotation accessory can be pressed on the surface with the electrical
tool put out of your control.
BA225S
/ II
950
8 5 . 00
125
M14
YES
2,0
9