Remote Control BIP
Characteristics
8 channels pre-associated to the O.C. outputs of INT4WS
Pressing one of the pushbuttons, it is possible to activate the O.C. regarding the "state" or "pulse" mode.
Pushbuttons association – Open Collector
C
h
a
n
1
2
1
2
3
5
4
3
4
5
6
7
8
Acquisition of remote controls
It is possible to acquire up to 16 remote controls which must be codified according to the chart attached
to the BIP.
It is not possible to acquire remote controls with the same codification.
In order to acquire a remote control, transmit in proximity of the receiver, remembering that the pressure
on a certain pushbutton will cause the corresponding O.C. on receiver to associate to the remote control
(see chart)
It is possible to acquire more pushbuttons and more remote controls (max 16)
e.g. if the pushbutton 1 and 5+2 are pressed, the remote control will activate the O.C. 1 and 6 (SPV)
1.
Move jumper S1 in PRG position
2.
make the transmission of the pushbuttons to be acquired
3.
LED related to acquired detector will switch on
4.
One or more LEDs according to signal received will switch on
5.
Once acquisition is over, move jumper S2 to position OPT
Note: the codification of the remote controls must be set as one, two, three, four up to max sixteen.
"State" or "Pulse" Function
When the pushbuttons are acquired, the O.C. output is associated in "state" activation mode.
It is possible to have the output associated to the remote control set in a "pulse" mode.
In order to make one or more outputs become "pulse" it is necessary to enter the programming mode
(SET PULSE OUTPUTS)
Take away supplying from board
1.
2.
move jumper S1 to position CLR
give again supplying to the board
3.
in this condition, transmit with any remote control and then press the pushbuttons corresponding
4.
to the outputs which must become "pulse
5.
move jumper S1 to position OPT
take away and then give supplying again
6.
Total Reset of INT4WS board
The reset of the factory settings and the cancellation of all remote controls and "state" or "pulse" setting of
O.C. outputs is obtained following the procedure of cancellation of detectors;
The reset of the settings occurs as soon as the procedure is started and confirmed by the Led flashing.
1.
move jumper S1 to position CLR.
2.
check LEDs flashing
3.
move jumper S1 to position OPT
A
P
u
s
h
b
t u
o t
n
s
n
e
s l
o t
p
e r
s
s
•
1
•
•
2
•
•
3
•
•
4
•
•
5
+
1
•
•
5
+
2
•
•
5
+
3
•
•
5
+
4
•
OPT
PRG
CLR
OPT
PRG
CLR
OPT
PRG
CLR
OPT
PRG
CLR
s
s
o
c
a i
e t
d
Pushbuttons functions
. O
. C
The pushbuttons from 1 to 4 directly activate the
1
Open Collector to which they are associated
2
The second group of pushbuttons is activated by
3
the contemporary pressure of pushbutton 5 (the
4
central one) and then one of the other pushbuttons.
B
A
T
S
P
V
Note: the O.C. from 1 to 4 become active if they are
N I
T
T
T
associated to both detectors and remote control
The O.C. from 5 to 8 , whether associated to the
remote control, loose their original function of
detectors "anomaly".
OPT
PRG
CLR
OPT
PRG
CLR
- 13 -
E
N
G