Publicité
Les langues disponibles
Les langues disponibles
O P E R A T I N G I N S T R U C T I O N S
Digital Pocket Sliding Calliper
150mm
Item-No. 81 60 33
Prescribed Use
The digital sliding calliper is used for measuring length of objects; besides, the internal diameter
e. g. of a pipe and also the depth e. g. of a bore hole can be determined.
Any use other than the one prescribed above could damage this product and might involve the
risk of short circuit, fire, electric shock, etc.
Always observe the safety notes included in these operating instructions.
If you hand the product over to third persons, also pass on these operating instructions!
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Included in package
• Sliding calliper
• Protective bag
• Battery (might be already inserted on delivery, possibly with protecting strip to prevent early
discharge)
• Operating Instructions
Safety Instructions
Please read all the instructions before using this device, they include impor-
tant information on its correct operation. The warranty will be void in the
event of damage caused by failure to observe these safety instructions! We
do not assume any liability for any consequential damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases.
• For safety reasons, any unauthorised conversion and/or modification to the prod-
uct is not permitted.
• The sliding calliper consists of conductive metal. For this reason, the sliding cal-
liper may not be used for measurements on live cables or objects; danger to life
by electric shock! Besides, the object to be measured may be damaged by a short
circuit!
• Do not apply the sliding calliper on sensitive objects or surfaces since the sharp
edges may cause scratch marks on the object to be measured.
• The product must not get damp or wet.
• Do not allow children to play with the device.
• Do not leave packaging materials unattended. They may become dangerous toys
for children.
• Handle the product with care, it can be damaged by impact, blows, or accidental
drops, even from a low height.
Controls
1 Surfaces for step measurements
2 Jaw for internal diameter
3 Display
4 Attachment screw
5 Handle
6 Jaw for external diameter or length measurements
7 Key "0" for zero position
8 Key "mm/in" to switch the measurement unit ("mm" or "inch")
9 "ON/OFF" button to turn on/off
10 Battery compartment cover
11 Thumb wheel to accurately slide the jaw
12 Feeler pin for depth measurements
General Battery Instructions
www.conrad.com
• Batteries should be kept out of children's reach.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by chil-
Version 05/09
dren or domestic animals. If swallowed, consult a doctor immediately.
°
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a fire.
There is a risk of explosion!
• Conventional batteries must not be recharged. Risk of explosion!
• Please observe correct polarity (plus/+ and minus/-) when inserting the battery.
Inserting/Replacing the Batteries
The battery compartment for a battery of type LR44/SR44 is located under a cover that is sim-
ply slid open. Insert a battery in such a way that the plus pole ("+") points outwards in your direc-
tion. The battery must be replaced if the contrast in the display starts to fade or the sliding cal-
liper can no longer be switched on.
Operation
• Switch the sliding calliper on or off by using the button "ON/OFF".
• With the button "0" the value display can be reset to "0". Thus, both an absolute measurement
and a relative measurement (difference) are possible.
• The key "mm/in" is used to switch between the measurement units "mm" and "inch".
• By means of the thumb wheel (11) the flexible measuring jaw can be slid more sensitively.
• Pay attention that the sliding calliper is not attached in a wedged or inclined fashion since this
may lead to faulty measurements. Please observe the following sample illustrations ("x"
stands for a faulty measurement):
Disposal
a) Product
b) Batteries and rechargeable batteries
The end user is legally obliged (Battery Regulation) to return used batteries and rechargeable
batteries. Do not dispose of used batteries via the domestic waste!
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical Data
Power supply................................................1 Battery of type LR44, AG13 or of identical design
Measurement range ....................................0-150mm
Definition ......................................................0.01mm (0.0005" resp.)
© Copyright 2009 by Conrad Electronic SE.
When disposing of an unserviceable product, do so in keeping with the relevant
statutory regulations.
Contaminated batteries/rechargeable batteries are labelled with these symbols to
indicate that disposal in the domestic waste is forbidden. The symbols for the rele-
vant heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead (marked on
batteries/rechargeable batteries, e.g. under the waste bin symbol on the left).
You can dispose of your used batteries/rechargeable batteries free of charge at
your community's collection point or any place where batteries/rechargeable batte-
ries are sold!
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
Publicité
