Pelican NEMO 2010 Recoil LED Mode D'emploi

NEMO 2010 Recoil
TM
OPERATING INSTRUCTIONS CATALOG #2010N
BATTERY INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp module.
3. Remove the battery tray.
4. Remove used batteries and replace with fresh
batteries in the tray as shown by the polarity
icons molded into the base of the tray battery.
5. Insert the battery tray into the flashlight with the two
metal tabs facing outwards.
6. Replace the lamp module.
7. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ON/OFF
Turn the lens housing clockwise until light activates.
To turn light off, back lens housing off counter-clockwise
until light goes off. Continue to back off for approximately 1
full turn to eliminate possibility of light activating accidentally
in storage. DO NOT OVERTIGHTEN.
LAMP REPLACEMENT
To replace the lamp module follow steps in the
battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #6 and #7.
SCUBA DIVING APPLICATION
(Follow these instructions whenever you replace the batteries)
Check closely for cuts, scratches, or otherwise
damaged o-ring or mating lens lip surface as
this can cause your light to flood instantly under
pressure. Remove any salt deposits, sand, dirt,
and foreign matter from O-ring sealing surfaces.
KEEP THREADS, O-RING GROOVE AND INSIDE LIP
OF LENS LUBRICATED WITH SILICONE GREASE.
Pelican Unconditional Lifetime
Guarantee of Excellence
If for any reason you are not satisfied with the qual-
ity or performance of any PELICAN product, we will
gladly replace the product or refund your money (at your
option) within 30 days of purchase through the original
retailer/dealer. PELICAN PRODUCTS will continue to
guarantee the product directly for a lifetime against
breakage or defects in workmanship. Lifetime guarantee
does not cover the lamp or batteries. The o-rings must
be kept greased (and replaced if damaged) per product
instructions. This guarantee is void only if the PELICAN
product has been abused beyond normal and sensible
wear and tear.
THE ABOVE GUARANTEE DOES NOT COVER
SHARKBITE, BEAR ATTACK OR CHILDREN UNDER 5.
PELICAN
You break it, we replace it... forever.
23215 Early Ave. • Torrance, CA 90505
(310) 326-4700 • FAX (310) 326-3311
www.pelican.com
LED
TM
CAUTION
If light is not to be used for some time, remove batteries
to prevent possible LEAKAGE AND CORROSION.
PRODUCT SPECIFICATIONS
Lamp Type:
Battery Burn Time:
Battery Type:
REPLACEMENT PARTS
2001 O-ring
If your local retailer does not stock the above accessory
parts, you may order them directly from Pelican Products.
Send check or money order in U.S. dollars, or order by
phone using MasterCard or VISA (ask for Customer
Service). SORRY, NO C.O.D.'s. California residents add
8 / % sales tax. Allow 2-3 weeks delivery time. Pelican
1
4
Products pays postage and handling charges.
POSTAGE PAID FOR U.S. ZIP CODE AREAS ONLY.
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which are present
to absorb hydrogen gas that could possibly be emitted by defective,
leaking, reversed polarity or heavily discharged batteries. If the pellets
become wet, let them air dry. Pelican Products assumes no liability
for any brand batteries which are defective or cause injury to anyone
when used in any Pelican flashlight.
Battery Replacement
Do not mix battery brands or use Nicad or Zinc Carbon Batteries. Do
not mix old and new batteries. Replace all batteries at the same time.
DO NOT MODIFY THIS PRODUCT!
23215 Early Ave. • Torrance, CA 90505 USA
Tel (310) 326-4700 • FAX (310) 326-3311 • www.pelican.com
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel (780) 481-6076 • FAX (780) 481-9586
PELI
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel (+34) 93.467.4999 • FAX (+34) 93.487.7393 • www.peli.com
All trademarks and logos displayed herein are registered and unregistered
trademarks of Pelican Products, Inc. and others.
2013-312-000
:
1W LED
50+ hours
E93 1.5V Alkaline C-cell (3)
2014 Lamp Module
Assembled
in the USA
PELICAN
You break it, we replace it... forever.
PELICAN CANADA
TM
PRODUCTS, S.A.
TM
© 2007 Pelican Products OC/07
NEMO 2010 Recoil
TM
INSTRUCCIONES DE FUNCIONAMIENTO #CAT. 2010N
INSTALACIÓN DE LAS PILAS
1. Retire el bastidor de la lente girándolo en sentido
contrario a las agujas del reloj.
2. Retire el módulo de la bombilla.
3. Retire la bandeja de pilas.
4. Retire las pilas usadas y coloque las pilas nuevas en la
bandeja teniendo en cuenta la polaridad como se mues-
tra en la ilustración impresa en la base de la bandeja.
5. Inserte la bandeja de pilas en la linterna con las dos
piezas metálicas apuntando hacia afuera.
6. Vuelva a colocar el módulo de la bombilla.
7. Vuelva a colocar el bastidor de la lente sobre la rosca y
gire en el sentido de las agujas del reloj al mismo
tiempo que ejerce un poco de presión sobre el mismo.
ENCENDIDO / APAGADO
La luz se enciende girando el bastidor de la lente en el
sentido de las agujas del reloj. Para apagarla, gire en
sentido opuesto hasta que se apague la luz. Siga girando
aproximadamente una vuelta completa para eliminar la
posibilidad de que la luz se encienda por error al estar
guardada. NO APRIETE DEMASIADO.
REEMPLAZO DE LA BOMBILLA
Para cambiar el módulo de la bombilla, siga los
|pasos especificados para la instalación de las pilas que
aparecen a continuación: Para retirar el módulo de la bombilla,
siga los pasos No. 1 y 2.
Para cambiar el módulo de la bombilla, siga los pasos No. 6 y 7.
CATALOG
PELICAN
#2010N
NEMO 2010
TM
Recoil
TM
OPERATING INSTRUCTIONS
SUBMERSIBLE TO 500 FEET
PELICAN
You break it, we replace it... forever.
23215 Early Ave. • Torrance, CA 90505
(310) 326-4700 • FAX (310) 326-3311
www.pelican.com
LED
TM
TM
LED