Publicité
Les langues disponibles
Les langues disponibles
d) Call functions
Function
Description
• Power ON: Press and hold the multifunction button approx.1 sec
Power ON /
• Power OFF: Press and hold the multifunction button approx. 5 sec. The
OFF
indicator will light red for 1 sec then go off. A voice will prompt "power off".
From standby mode: Enable / disable by pressing and holding the
Voice control
multifunction button approx.1 sec
End call
Press the multifunction button (6) or place the earpiece in the receptacle (3) .
When an incoming call is received, press and hold the multifunction button
Reject call
for approx. 1 sec.
Press the multifunction button to receive an incoming call <or> take the
earpiece out of the receptacle.
Receive call
Answering calls by taking the earpiece out of the receptacle
works with iPhones running iOS 8.4 or higher, and most Android
devices.
• Enter standby mode by stopping any playback or ending any calls.
Redial last
number
• Double press the multifunction button to redial the last number.
Call
During a call, press and hold the multifunction button approx.1 sec. A long
forwarding
beep will sound to indicate the call has been forwarded.
During a call, double press the multifunction button. A beep will sound to
Mute calls
indicate that the call has been muted.
Music on/
Press the multifunction button to play a song and press again to pause the
pause
song.
If a caller "B" is calling during an on-going call "A":
• Press the multifunction button to release caller A and answer B.
<or>
Three-way
• Double press the multifunction button to put A on hold and answer B.
calling
- Double press the multifunction to switch between A and B.
- Press the multifunction button to release the current caller and recover
the held call.
e) 1 to 2-point connection
1. Pair the headset with phone A then disable the Bluetooth function of A.
2. Pair the headset with phone B then enable the Bluetooth function of B.
- If your cell phone supports automatic reconnection, the earpiece will be automatically
connected to A.
- Alternatively, you can press the multifunction button to reconnect to A.
3. The Bluetooth headset should now be connected to A and B.
f) Anti-lost warning
If the earpiece is more than 10 m away (open area) from the mobile phone or is unexpectedly
disconnected:
The purple LED will flash 3 times every 5 seconds. After this,the blue LED will start to blink
immediately, accompanied by 2 beeps.
Troubleshooting
Problem
Cause
The battery has run out.
The earpiece cannot
The power button is not
be powered on.
pressed and held long
enough.
The earpiece cannot
The earpiece is not
be powered off.
functioning correctly.
The earpiece is not in
pairing mode.
Pairing fails
The Bluetooth application
of the cell phone is in
error.
Suggestion
Charge the battery.
Press and hold the power button
again.
Reset the earpiece by placing it
into the charger and removing it.
Turn the earpiece off then on
again.
Restart your mobile device and
try again.
Care and cleaning
• Disconnect the product from the power supply before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, lint-free cloth.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this
product conforms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Select a language by clicking on a flag symbol and enter the product order number
in the search box. You can then download the EU declaration of conformity in PDF
format.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines. You thus fulfill your statutory obligations and
contribute to the protection of the environment.
Technical data
a) Charger
Input voltage ................................. 12 V/DC (rated operating voltage)
12 - 24 V/DC (limit working voltage)
USB-A port .................................... 4.75 V - 5.25 V
2.1 A (Rated)
2.4 A (Max.)
Standby power consumption ........ 1 W
Operating/Storage conditions ....... -10 to +50 ºC, 10 – 90 % RF (non-condensing)
Dimensions (W x H x D) ............... 42 x 42 x 91 mm
Weight .......................................... 33 g
b) Bluetooth earpiece
Battery .......................................... LiPo 3.7 V 35 mAh
Bluetooth name ............................ RF-CCB-200
Sound ........................................... Mono
Sound pressure ............................ 102 ±3 dB
Bluetooth profile ............................ A2DP, AVCRP, HFP, HSP
Bluetooth version .......................... 4.0
Frequency ..................................... 2.402 - 2.480 GHz
Transmission power...................... <4 dBm
Transmission distance .................. 10 m
Frequency response ..................... 10 - 50 kHz
Transmit power ............................. Class 2
Time .............................................. Playback: 1.5 hrs
Talk: 2 hrs
Standby: 50 hrs
Charging: 2 hrs
Mic type ........................................ Omni-directional, condenser
Operating/Storage conditions ....... -10 to +50 ºC, 10 – 90 % RF (non-condensing)
Dimensions (W x H x D) ............... 25.3 x 25.5 x 27.5 mm
Weight .......................................... 5 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
*2176934_v2_0420_02_dh_m_en
Publicité
