LOVATO ELECTRIC EXM10 12 Manuel page 6

GB
TECHNICAL CHARACTERISTICS
Auxiliary supply
Rated voltage Us
Operating voltage range
Frequency
Power consumption/dissipation
Immunity time for micro breakings
RS485 serial interface
Baud-rate
Relay outputs (EXM10 20 only)
Number of outputs
Type of output
Rated operating voltage
IEC/EN 60947-5-1 designation
NO contact
NC contact
Electrical life
Mechanical life
Insulation between the 2 relay outputs
Ambient conditions
Operating temperature
Storage temperature
Relative humidity
Maximum pollution degree
Overvoltage category
Altitude
Climatic sequence
Shock resistance
Vibration resistance
Insulation
Rated insulation voltage Ui
For voltage groups
Between Power Supply and RS485
Between Power Supply and Outputs
Between RS485 and Outputs
Between the two relay outputs ‚
6
100 - 240V~
110 - 250V=
85 - 264V~
93,5 - 300V=
45 - 66Hz
EXM10 12 – 3.2VA 1W
EXM10 20 – 5.8VA 1.5W
≥50ms
1200...38400 bps programmable
2
1 changeover contact NO/NC
250V~
AC1 5A-250V~ 5A 30V=
AC1 3A-250V~ 3A 30V=
D300
3
NO contact – 20x10 ops
3
NC contact – 10x10 ops
7
10 ops
Single ‚
-20 - +60°C
-30 - +80°C
<80% (IEC/EN 60068-2-78)
2
III
≤2000m
Z/ABDM (IEC/EN 60068-2-61)
15g (IEC/EN 60068-2-27)
0.7g (IEC/EN 60068-2-6)
250V~
Impulse withstand Power frequency
Uimp withstand
7.3kV 3kV
4.8kV 1.5kV
7.3kV 3kV
4.8kV 1.5kV
Auxiliary supply connections
Type of terminal
Number of terminals
Conductor cross section (min...max)
Tightening torque
RS485 port connection
Type of terminal
Number of terminals
Conductor cross section (min...max)
UL Rating
Conductor cross section (min... max)
Tightening torque
Relay output connection (EXM10 20 only)
Type of terminal
Number of terminals
Conductor cross section (min... max) /
UL rating
Tightening torque
Minimum temperature of connection cables
EXM10 12
EXM10 20
Housing
Version
Mounting
Material
Degree of protection
Weight
Certifications and compliance
Certifications
UL Marking
NO
NC
Compliant with standards
‚
Both relay outputs must be used with the same voltage group.
CLASS 1 LED PRODUCT
INVISIBLE LED RADIATION
950 nm, max 50 W
IEC/EN 60825-1:1994 + A1:2002 +
A2:2001
Screw (fixed)
2 + 2 for auxiliary supply
2
0.2...4.0 mm (24...12 AWG)
0.8Nm (7lbin)
Plug-in / removable
4
0.2...2.5 mm² (24...12 AWG)
0.75...2.5 mm² (18...12 AWG)
0.5 Nm (4.5 lbin)
Screw (fixed)
6
0.2...2.5 mm² (24...12 AWG)
0.44 Nm (4 lbin)
70°C
80°C
2 module (DIN 43880)
35mm DIN rail (IEC/EN 60715)
or by screw using extractible clips
Polyamide RAL7035
IP40 on front
IP20 terminals
140g
cULus
Use 60°C/75°C copper (CU) conductor only.
For electrical ratings - Supply voltage, Field
wiring terminals tightening torque and AWG
range, stranded or solid - see indications above).
– 30VDC 5A resistive; 250VAC, 50A general use,
D300 Pilot Duty
– 30VDC 3A resistive; 250VAC, 3A general use
IEC/EN 61010-1, IEC/EN 61000-6-2,
IEC/ EN 61000-6-3, UL508 e CSA C22.2-N°14