Using The Remote Control; Cr-340 Remote Control - Arcam AVR100 Manuel

Using the remote control

CR-340 Remote Control

The CR-340 remote control gives access to all functions
available on the front panel, plus some additional functions
only available from the remote. It also has controls to
operate Arcam CD and DVD players.
Source selection buttons
These operate in the same way as the source selection buttons
on the front panel of your AVR100 amplifi er.
Displays Radio Data System (RDS) text information, if available.
Press again for station frequency, and again to show station
information (the default mode).
Selects the multi-channel output from a DVD audio player or
external decoder source connected to the 5.1 channel input.
Switches the amplifi er into stand by mode after a preset number
of minutes. Pressing once will set the sleep time to 90
SLEEP
minutes. 'SLEEP MODE' is shown on the display panel.
Each consecutive press of
SLEEP
30 minutes. Sleep mode is cancelled by setting the time to 0
minutes, or by pressing the
POWER
Allows direct access to trim the centre, rear and subwoofer
speaker outputs. Press TRIM to cycle between channels and use
the and
Scrolls through the available surround sound modes (Stereo,
Pro Logic, and Hall effect). The selection is shown in the display
Compresses the dynamic range for low-level listening of Dolby
Digital sources. The dynamic range may be set from 100% (the
default) to 25% (maximum compression) in steps of 25%. The
reduction is shown on the display.
The button toggles the remote control unit into
CD/DVD
controlling an Arcam CD or DVD player: this setting is briefl y
confi rmed by a light at the top of the controller.
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control!
Do not place anything in front of the display area on the
AVR100 (where the IR receiver is located), or the remote
control may not work.
CD
SAT
TAPE
RDS INFO
INFO
5.1
SLEEP
reduces the sleep time by
or button.
STANDBY
TRIM
arrows to adjust levels.
•
MODE
area for three seconds.
DYNAMIC RANGE
DVD DVD
MODE MODE
CD/DVD functions
CD/DVD lights
These indicate the function of the CD/DVD button at the bottom of
the control. They are not related to any function on the AVR100.
The LED only stays on for 15 seconds to conserve battery life. If
neither LED is lit this does not mean that the remote control unit
is not working!
Power/Standby
Toggles the amplifi er between stand by mode and full power
AV
DVD mode. The power indicator light next to the power button on the
front panel is red when the amplifi er is in stand by and green
when powered up.
DVD VCR AUX
P–/P+
CD FM AM
Cycles through preset radio stations, or scans through frequency,
depending on the Tuner mode setting.
T
P P+
MODE
5 1
TUNER MODE
Toggles between Preset mode and Tune mode. See 'Tuner
controls' for details.
SLEEP TEST
TEST
Engages the test signal generator so that the volume for each
channel can be balanced from your listening position. The signal
OK
moves from Front Left to Centre, Front Right, Rear Right, Rear
Left and Subwoofer in a continuous cycle. Note that the test
signal may not be heard through a subwoofer.
See 'Using the On Screen Display' for full instructions on this
feature.
Cursor pad and OK button
These are used to navigate through the pages in the on screen
display (OSD). See 'Using the On Screen Display'.
TRIM
MODE
VOLUME and MUTE ( )
DYN
Press
on the amplifi er.
Press
CD CD
Both tape outputs and the headphone socket remain active. In
mute mode the display fl ashes 'MUTING'.
ENTER ENTER
Mute is disabled either by pressing
volume. Note that the volume and mute controls have no effect
on the output levels of Arcam CD players.
CD/DVD
CR-340
to increase volume or to decrease the output volume
+ –
to mute the speaker connections and pre-amp outputs.
again, or by adjusting the
AVR100
13