Casals CSS710VCE Notice Originale page 7

label Replacement of carbon brush (Fig D)
e ap- - Remove the carbon brush lid (6) with a screw-
driver.
- Replace the carbon brush.
- Install the carbon brush lid (6) with a screwdriver.
it off
Use:
paper - Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
edge - Assemble the sanding Sheet
- Turn the appliance on, by using the on/off button
) and (1).
- Place the appliance against the surface you want
l it off to work.
- Slowly move the appliance over the workpiece,
- Do not apply excessive pressure against the work-
piece.
- Apply uniform sanding pressure against the work-
piece to increase performance and working life of
n the the sander and the sanding sheet.
Once you have finished using the appliance:
- Stop the appliance using the on/off switch (1).
- Unplug the appliance from the mains.
- Clean the appliance.
ed by
nction Cleaning
pt the - Disconnect the appliance from the mains and al-
needs low it to cool before undertaking any cleaning task.
- Allow it to cool before undertaking any cleaning
task.
- Clean the electrical equipment and the mains
f but- connection with a damp cloth and dry. DO NOT IM-
MERSE IN WATER OR ANY OTHER LIQUID.
cking - Clean the equipment with a damp cloth with a few
1). drops of washing-up liquid and then dry.
on (1) - Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
- Do not let water or any other liquid get into the
e pad air vents to avoid damage to the inner parts of the
appliance.
- Never submerge the appliance in water or any
tion. other liquid or place it under running water.
- If the appliance is not in good condition of cleanli-
ness, its surface may degrade and inexorably affect
the duration of the appliance's useful life and could
become unsafe to use.
t 12 Supplies
o lock - Always use original supplies, designed specifically
for your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical
support service if a product damage or other
problems arise. Do not try to dismantle or repair
without assistance, as this may be dangerous.
- If the connection to the mains has been damaged,
it must be replaced and you should proceed as you
would in the case of damage.
Specifications:
- Rated power
- Rated voltage
- No load speed
- Sandpaper dimensions
- Weight
- Sound Pressure level (LpA) =
- Sound Power level (LwA) =
- Vibration=
NB: These specifications are subject to change without
notice of purpose of improvement.
NB: By virtue of the conditions of fabrication of this
product, the maximum absorbed power can differ from
that specified.
NB: By virtue of the conditions of fabrication of this
product, the maximum used power can differ from that
specified.
Wear hearing protection
-Measured sound level
EN60745
-The vibration emission level given in this information
sheet has been measured according EN60745 and
may be used to compare one tool with other. It may be
used for a preliminary assessment of exposure
-The vibration value during actual use of the power
tool can differ from the declared total value depending
on the way in which tool is used
-It's necessary identify safety measures to protect the
operator that are based on an estimation of exposure
in the actual conditions of use (taking account of all
parts of the operating cycle such as the times when
the tool is switched off and when it is running idle in
addition to the trigger time).
For EU product versions and/or in case that it is
requested in your country:
Ecology and recyclability of the product
CSS710VCE
710 W
230 V~
1500-3000 /min
Ø 180
2.3 Kg
90.9dB(A), KpA = 3dB
101.9 dB(A), KWA = 3dB
2.415m/s2, K= 1,5 m/s2
determined according
7