Publicité
Les langues disponibles
Les langues disponibles
•
click the second button to the left in the blue bar at the bottom.
•
We recommend selecting "Bridge", the second mode option listed in the dropdown menu.
connects to your router as the default gateway. Thus you will be able to access your network
normally, even if your device is currently connected to the repeater.
separate network.
• After that click in the list below on the WLAN that your repeater should use to connect to
or you wish to extend.
You can refresh the list by clicking the two round arrows.
•
the end of the name. You could however change the two names, is you like.
• Now you still need to enter the password of the WLAN network that you have selected
• Last but not least, click the blue button to connect. Once the changes have been applied,
the set-up is complete.
to the new WLAN network.
If you would like to make other changes to the settings, click on the Setup button in
the lower right corner of the web interface. The current status of the device is shown
under Status.
Positioning of the "Repeater"
•
tion as shown in the following illustration.
• Try several locations and then select the best place with the best connection to your existing
WLAN router.
• At least 2 LEDs of the WLAN should be lit to indicate that your repeater is not placed too
far away from your router.
Resetting to factory settings
Proceed as follows to reset the product to factory settings.
• Plug the device into a mains socket.
• Use the slider (3) to switch on your device and wait until the start-up process has completed.
• Hold down the sunk button (1) for more than 3 seconds. Then release the button again.
• The product will restart with the factory settings. This process will last approx. 2 minutes.
Care and cleaning
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions
since these could damage the housing or even impair operation.
• Always unplug the product from the power socket and disconnect all the connecting cables
before cleaning it.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electrical and electronic equipment does not belong in the regular household waste.
Once the product becomes unusable, dispose of it in accordance with the relevant
statutory regulations.
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the 2014/53/EU directive.
The full text of the EU conformity declaration is available via the following Internet
www.conrad.com/downloads
conformity in PDF format.
Technical data
Operating voltage ................................. 100 - 240 V/AC, 50/60 Hz, max. 0.3 A
Ports ..................................................... 1x RJ45 LAN 100 Mbit; 1x RF45 WAN/LAN 100 MBit
WLAN ................................................... EEE802.11b/g/n, 2.4 GHz, max. 300 MBit;
Transmit frequency range ..................... 2.412 – 2.472 GHz, 18.02 dBm;
Encryption protocols ............................. WPA2; WPA
Operation modes .................................. Repeater; Access Point; Router
Dimensions (W x H x D) ....................... approx. 50 x 73 x 52 mm (without antennas)
Dimension antennas (Ø x L) ................. approx. 10 x 91 mm
Weight .................................................. approx. 111 g
Operation conditions ............................. 0 °C to +40 °C, max. 10 - 90% rF
Storage conditions ................................ -10 °C bis +70 °C, 10 - 90% rF (noncondensing)
-
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2019 by Conrad Electronic SE.
IEEE802.11a/n/ac, 5 GHz, max. 867 MBit;
5.180 – 5.240 GHz, 18.42 dBm
(relative air humidity, noncondensing)
1902086_V1_0519_02_m_VTP_en
-
Publicité
