Publicité
Les langues disponibles
Les langues disponibles
"Repeater" quick set-up via WPS
Please note that the mode selection slider (6) must be in the „Repeater" position, if
The repeater clones the WLAN name and password of your wireless LAN router dur-
name so that you you are able to distinguish between your router's wireless network
and that of the repeater's.
•
for about 6 seconds.
• Press the WPS button on your WLAN router within 2 minutes. Alternatively, you could also
use the WPS function on the router's web interface.
Please refer to the operating instructions of your router.
•
your wireless network connection is shown by means of the 3 WiFi LEDs.
•
WLAN password is the same as your router's WLAN password.
Now you could also connect devices to the other two network ports.
Operating modes overview and web interface access
a) "Repeater" mode
•
on the web interface (like setting the region and changing the login password) (see chapter
•
• In either case, you should connect a computer or mobile device to the wireless LAN or to
router password for the WLAN; otherwise your wireless local area network is not encrypted.
•
and on again). Alternatively, you could use the IP address to open the web interface. Since
the repeater is already integrated in your network, you can look up the IP address of your
WLAN router. Please refer to the manual of your router.
b) "Access point" mode
• As soon as the access point is correctly connected to your router, it is usually ready for use.
• Connect a computer or a mobile device to the WLAN or the LAN port of the AP.
•
If the web page does not load, use the IP address to open the page. Since the AP is already
integrated in your network, you can look up the IP address of your WLAN router. Please
refer to the manual of your router.
c) "Router" mode
• Connect a computer or a mobile device to the WLAN or to the LAN port of the router.
•
dress 192.168.10.1 to do this.
•
d) Log in to the web interface (all modes)
•
• Enter the default password admin
(2) on the repeater
http://ap.setup.
192.168.10.1.
http://ap.setup.
http://ap.setup or the default IP ad-
• In the web interface select your region and your time zone.
• Then enter a new web interface password.
•
But you can of course change other settings later.
use the login password you have just created; don't enter the default login pass-
word.
•
the second button to the left in the blue bar at the bottom.
• You could also change the two names of the WLAN networks (2.4 and 5 GHz).
• Now choose the WLAN encryption. We recommend selecting WPA2-PSK, which offers
the highest security. However, if you have devices, which only support WPA, select both
standards.
• Enter your WLAN password. Your password should consist of at least 8 characters and
include numbers as well as upper and lower case letters.
•
is complete.
to the new WLAN network.
If you would like to make other changes to the settings, click on the Setup button
in the lower right corner of the web interface or on the Wi-Fi button for the WLAN
settings. The current status of the device is shown under Status.
•
click the second button to the left in the blue bar at the bottom.
• Select the Internet access type. If you have for example a DSL connection with your access
data, select PPPoE here.
•
• You could then also change the two names of the WLAN networks (2.4 and 5 GHz).
• Now choose the WLAN encryption. We recommend selecting WPA2-PSK, which offers
the highest security. However, if you have devices, which only support WPA, select both
standards.
• Enter your WLAN password. Your password should consist of at least 8 characters and
include numbers as well as upper and lower case letters.
•
is complete.
to the new WLAN network.
If you would like to make other changes to the settings, click on the Setup button
in the lower right corner of the web interface or on the Wi-Fi button for the WLAN
settings. The current status of the device is shown under Status.
Publicité
