Porter Cable PC60TPAG Manuel D'instructions page 3

g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4) PoWeR tool uSe ANd cARe
a) do not force the power tool. use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
f) keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) use the power tool, accessories and tool bits, etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
5) SeRvIce
a) have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
SAfety INStRuctIoNS foR All oPeRAtIoNS
SAfety WARNINGS coMMoN foR GRINdING, SANdING,
WIRe BRuShING oR ABRASIve cuttING-off oPeRAtIoNS
a) this power tool is intended to function as a grinder, wire brush, sander
or cut-off tool. Read all safety warning instructions, illustrations and
specifications provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury. operations
such as polishing are not recommended to be performed with this power
tool. Operations for which the power tool was not designed may create a hazard
and cause personal injury.
b) do not use accessories which are not specifically designed and
recommended by the tool manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe operation.
c) the rated speed of the accessory must be at least equal to the maximum
speed marked on the power tool. Accessories running faster than their rated
speed can break and fly apart.
d) the outside diameter and the thickness of your accessory must be within
the capacity rating of your power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
e) the arbor size of wheels, flanges, backing pads or any other accessory must
properly fit the spindle of the power tool. Accessories with arbor holes that do
not match the mounting hardware of the power tool will run out of balance, vibrate
excessively and may cause loss of control.
f) do not use a damaged accessory. Before each use inspect the accessory
such as abrasive wheel for chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an accessory, position yourself
and bystanders away from the plane of the rotating accessory and run the
power tool at maximum no-load speed for one minute. Damaged accessories
will normally break apart during this test time.
g) Wear personal protective equipment. depending on application, use face
shield, safety goggles or safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and work shop apron capable of stopping small
abrasive or workpiece fragments. The eye protection must be capable of
3