Operation - Hart HPIF50 Manuel D'utilisation

OPERATION

For complete charging instructions, see the operator's
manuals for your battery pack and charger.
MODE/POWER BUTTON
See Figure 2, page 9.
 P ress the mode/power button to turn on the unit.
 T o turn off the unit, press and hold the mode/power button
until the light turns off, then release the button.
AUTOMATIC SHUTOFF
The digital gauge will remain on for up to five minutes. To
manually shut off, press and hold the mode/power button
until the light turns off, then release the button.
DIGITAL GAUGE
See Figure 2, page 9.
The digital gauge is multifunctional, serving as a pressure
gauge and monitoring the amount of pressure being applied
to the item being inflated. Pressure is indicated by PSI.
 P ress the mode/power button to turn on the digital gauge.
The unit will start up in high pressure mode by default.
NOTE: Make sure digital gauge is set at 0 before use. If
gauge reads "Err" or needs to be reset to 0, press and
hold both the mode/power button and start/stop button
at the same time for approximately 5 seconds.
 P ress the mode/power button again to select the low
pressure mode. Pressing the button one more time selects
high pressure mode. The selected mode is indicated by
the arrow on the left or right side of the display. Modes
can be selected back and forth by pressing the mode/
power button.
NOTE: After a high pressure preset has been set, the
pressure setting stays in the memory until the unit is
turned off. To recall the previous pressure setting after
inflation, press the ( + ) or ( – ) button.
DUAL HOSES
See Figures 3-5, pages 9-10.
WARNING:
Improperly attached hoses or accessories can become
detached under pressure and cause serious injury.
Possible air leaks can cause faulty pressure readings.
Make sure all connections are tightly secured.
The inflator has two hoses for two types of inflation. The
high pressure hose is for inflating high pressure items like
tires and sports balls. The low pressure hose is designed
for inflating or deflating low pressure, high volume items like
air rafts, mattresses, and floats.
NOTE: Pressure gauge and preset features are relative only
to high pressure hose applications.
INFLATING WITH THE HIGH PRESSURE HOSE
See Figure 6-7, page 10.
The air chuck on the high pressure hose can be used without
adaptors to inflate tires or with any application that has a valve
stem that fits the air chuck opening.
NOTE: When inflating items of 10 PSI or less, inflate in short
bursts and check after each burst by feel or with a calibrated
measuring device to determine accurate pressure.
 P ress the mode/power button to turn on the digital gauge.
The unit will start up in high pressure mode by default.
NOTE: Make sure digital gauge is set at 0 before use. If gauge
reads "Err" or needs resetting, press and hold both the mode/
power button and start/stop button for about 5 seconds.
 S et desired pressure.
 T hread air chuck onto the valve stem, making sure it is
tightened securely. Do not cross-thread.
NOTE: The current air pressure inside the item will be shown
on the display.
 P ress the ( + ) or ( – ) button to select the needed air pressure.
Press and hold the ( + ) or ( – ) button to increase or decrease
the air pressure in 5 PSI increments.
 P ress the start/stop button to start inflating.
NOTE: The pressure readout on the gauge while inflating
is a measurement of the fluctuating pressure between the
item and the high pressure hose. To get an accurate reading,
stop inflating and follow above instructions for reading the air
pressure.
NOTE: Stand 10 feet away from item during inflation.
 T urn off the inflator and store the hose in the hose wrap on
the side of the unit.
 P ress and hold the mode/power button to deactivate the
display.
INFLATING MANUALLY FOR HIGH PRESSURE
APPLICATIONS
 C onnect the high pressure hose to item to be inflated.
 P ress mode/power button to select high pressure.
 P ress and hold start/stop button until desired pressure is
reached.
 T urn off the inflator and store the hose in the hose wrap on
the side of the unit.
INFLATING WITH THE HIGH PRESSURE AIR
HOSE AND ACCESSORIES
See Figures 8, page 10.
The high pressure air hose can be used with the provided
adaptors to inflate a variety of items.
 T o install accessory, thread adaptor (or needle) into air
chuck. Inflate to desired pressure.
 R emove accessory after inflating and return to storage
area on the side of the unit.
6 – English