Publicité
Les langues disponibles
Les langues disponibles
Important Safety Instructions
• Clean up all removed paint and dust
by wet mopping the floors. Use a wet
cloth to clean all walls, sills and any other
surface where paint or dust is clinging. DO
NOT SWEEP, DRY DUST OR VACUUM.
Use a high phosphate detergent or
trisodium phosphate (TSP) to wash and
mop areas.
• At the end of each work session put
the paint chips and debris in a double
TO OPERATE HEAT GUN
1. Plug heat gun into properly rated outlet.
2. Move rocker switch to "II" position. (VT
Models, turn heat control to desired
heat setting). Heat
gun will come up
to full operating
temperature in
approximately two
minutes.
3. Adjustable stand
is provided to allow
nozzle to be rotated
from almost horizontal
to vertical position.
4. To turn heat gun off
after use, move
switch to "I" position.
Run on cold for
approximately three
minutes. This will
allow the heat gun to
cool down and the
nozzle to become
cool to the touch.
5. Move switch to
"O" position.
NOTICE: When heat gun is used in an
enclosed container, such as a shrink tunnel
or special enclosure, ambient air must be
allowed to pass into the heat gun and there
must be an outlet of equal size for the
CLEANING
Unplug heat gun before cleaning. To clean
outside of tool, use only a mild soap and
damp cloth. Do not use other cleaning
agents, turpentine, gasoline, lacquer or paint
thinner, or other solvents that may contain
4
plastic bag, close it with tape or twist ties,
and dispose of properly.
• Remove protective clothing and work
shoes in the work area to avoid carrying
dust into the rest of the dwelling. Wash
work clothes separately. Wipe shoes off
with a wet rag that is then washed with
the work clothes. Wash hair and body
thoroughly with soap and water.
heated air to pass out of the enclosure
also. Total enclosure will cause damage or
A LA SORTIE.
DU BEC OPÉRER À 'COLD'
AVANT DE FERMER
-CAUTION-
possible failure to the heat gun due to the
HIGH TEMPERATURE AT
NOZZLE. RUN ON 'COLD'
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
extreme heat generated.
For typical applications and tips please
consult www.masterappliance.com.
If you have any questions regarding your
specific application or use, feel free to call our
Customer Service Department at
VT Model
262-633-7791.
NOTICE: Users should independently
evaluate the suitability of the product for
their application.
NOTICE: The HG-201D/202D and
A LA SORTIE.
DU BEC OPÉRER À 'COLD'
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
VT-751D/752D element is protected by a
NOZZLE. RUN ON 'COLD'
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
self-resetting fuse. If element does not
heat, unplug the unit for several minutes,
then follow operating instructions to use.
NOTICE: The element in the T-series
models is protected by a one-shot fuse.
A LA SORTIE.
DU BEC OPÉRER À 'COLD'
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON 'COLD'
BEFORE TURNING OFF.
If element does not heat, element may
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
need replacing.
Of Fire Or Electric Shock, Connect To
Grounded Outlet. Do Not Expose To
Rain Or Moisture. Store Indoors; Read
Instruction Manual Before Using.
AT NOZZLE. RUN ON COLD BEFORE
TURNING OFF.
chemicals which are harmful to plastics and
other insulating materials. Never immerse
tool in a liquid or allow a liquid to enter inside
the tool. Make sure all vents and openings
are free and clear of debris.
WARNING - To Reduce The Risk
CAUTION - HIGH TEMPERATURE
www.masterappliance.com
Publicité
