Installation; Stove Placement; Floor Protection Requirements - CASTLE HPS10IC Manuel De L'utilisateur

INSTALLATION

It is recommended the stove be installed and serviced by
authorized professionals who are certified by the National
Fireplace Institute (NFI) as NFI Pellet Specialists.
Proper installation of this stove is necessary for safe and efficient
operation. Installing this product improperly may result in a
house fire and personal injury. All applicable building codes for
your location must be followed. In areas where building codes
require additional steps to the installation of this product not
included in this manual, the building codes will take precedent
and must be followed. Contact your local building inspector to
obtain any necessary permits or inspection guidelines before
installing the product.

STOVE PLACEMENT

Sketch out a plan for installing the stove including dimensions
before permanent placement. When determining the location
for the stove, wall stud location is critical. You may need to adjust
the location of the stove to avoid trying to vent through a wall
stud. Before placing the pellet stove, connect the vent and allow
for minimum clearance to combustible walls.

FLOOR PROTECTION REQUIREMENTS

The stove must be installed on a noncombustible floor, with
proper floor protection, or on a masonry hearth. When a clean
out t-vent is installed in the inside of a home, the floor protector
must extend 2" beyond rear of t-vent. SEE FIGURE 1. When stove
is vented straight through the wall and the clean out t-vent is on
the exterior of the home, the minimum clearance is 2" from the
back of the stove to the wall. SEE FIGURE 2. The minimum floor
protector material is 24 GA sheet metal.
2"
6"
6"
6"
Figure 1
Figures 1 and 2: Pellet stove floor pad clearances
10
2"
6"
6"
6"
Figure 2
Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5 CST
WARNING
READ THIS ENTIRE MANUAL BEFORE YOU INSTALL
AND USE THIS STOVE. FAILURE TO FOLLOW THE IN-
STRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY, OR EVEN DEATH.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST
VENTING SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE
HAZARDS OF HIGH SURFACE TEMPERATURES AND
SHOULD STAY AWAY TO AVOID BUMPS TO SKIN AND/
OR CLOTHING.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPER-
VISED WHEN THEY ARE IN THE SAME ROOM AS THE
STOVE.
CLOTHING AND OTHER FLAMMABLE MATERIALS SHOULD
NOT BE PLACED ON OR NEAR THIS UNIT.
CAUTION
THIS STOVE SHOULD NOT BE USED AS THE ONLY
SOURCE OF HEAT IN THE HOUSE. POWER OUTAGES
AND PERIODIC MAINTENANCE WILL RESULT IN A TOTAL
LOSS OF HEAT.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.
CONTAC T YOUR LOC AL AUTHORIT Y (SUCH AS
M U N I C I PA L B U I L D I N G D E PA R T M E N T, F I R E
DEPARTMENT, FIRE PREVENTION BUREAU, ETC.) TO
DETERMINE THE NEED FOR A PERMIT.
KEEP COMBUSTIBLE MATERIALS (SUCH AS GRASS,
LEAVES, ETC.) AT LEAST 3 FEET AWAY FROM THE FLUE
OUTLET ON THE OUTSIDE OF THE BUILDING.
INSTALLATION AND REPAIR OF THIS PELLET STOVE
SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE
APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT
LEAST ANNUALLY BY A QUALIFIED SERVICE PERSON. IT IS
IMPERATIVE THAT CONTROL COMPARTMENTS, FIRE BOX,
AND CIRCULATING AIR PASSAGEWAYS OF THE STOVE BE
KEPT CLEAN.
Operator's Manual
HPS10IC Pellet Stove