Speaka Professional 1693321 Mode D'emploi page 4

c) Power supply
The device is only to be supplied with power via the HDMI interface. However, this
must be supported by the connected HDMI device. Depedending on the connected
devices, not all HDMI devices provide adequate power supply for the HDMI audio
extractor.
In this case, you can supply the HDMI audio extractor with power via the
5 V/DC port (4) as described below. If the HDMI audio extractor works without the
5 V/DC port (4), this connection does not have to be made.
• Connect the small plug of the included USB cable to the USB/POWER port (4).
• Plug the large USB plug of the USB cable into a USB interface or into the USB port of a USB
power adapter.
HDMI IN
POWER
Troubleshooting
No audio signal available
• Check if the playback device has an audio signal.
• If necessary, select a different audio format (e.g., in the menu of the Blu-ray player and in the
audio settings of the Blu-ray disc).
The HDMI output (2) and the audio output (1) can provide the following audio signals:
Audio signal HDMI output (2)
2CH yes
LPCM5.1 yes
LPCM7.1 yes
Bitstream 5.1 yes
Bitstream 7.1 yes
• Control the volume settings of the connected devices.
• Check whether the mute function is enabled at one of the connected devices.
• The audio extractor can only function if energized. It might be necessary to connect the USB/
POWER port (4) to a USB power supply.
No image
• Select the proper input on the TV set/monitor.
• If the Blu-ray player has various outputs, check in the set-up menu of the Blu-ray player
whether the proper output is activated.
• TV set/monitor must support the playback mode (e.g., 3D).
• First check whether the TV set/monitor is working properly when connected directly to the
Blu-ray player (without the HDMI Audio Extractor).
• Then check the connection of the cable/plug between the HDMI Audio Extractor and the TV
set/monitor or Blu-ray player. Replace damaged cables.
Appropriate HDMI cables must be used for 3D playback.
• To play back copy-protected films, the TV set/monitor should support HDCP standard.
• The resolution (or colour depth) of the playback signal from the Blu-ray player is too high for
the TV set/monitor. The TV set/ monitor shows, for example the message "Mode not sup-
ported" or similar (signal is not supported).
• For the purpose of testing, use a shorter cable.
• The audio extractor can only function if energized. It might be necessary to connect the USB/
POWER port (4) to a USB power supply.
HDMI OUT
AUDIO OUT
Audio output (1)
yes
no
no
no
no
Handling
• Never use the product immediately after moving it from a cold room into a warm one. The
condensation that forms may damage the product under certain circumstances.
Allow the product to reach room temperature before connecting it to the power supply and
putting it into use. In some cases, this may take several hours.
• When setting up the product, make sure that the cables are neither kinked nor pinched.
• Always lay the cables so that nobody can trip over or become entangled in them. There is
a risk of injury.
Maintenance and cleaning
The product does not require any maintenance and should never be disassembled for any
reason. Any maintenance or repair work may only be performed by an expert.
Disconnect the product from the power supply before cleaning.
The outside of the housing should only be cleaned with a clean, soft, dry cloth. Do not use
aggressive cleaning agents or chemical solvents. This could damage the case (discolouration)
or impair its function.
Dust can easily be removed using a clean, long-bristle brush and a vacuum cleaner.
Disposal
Electronic devices are recyclable and do not belong in the household waste. Dispo-
se of an unserviceable product in accordance with the relevant statutory regulations.
Technical data
Operating voltage ......................... 5 V/DC (via HDMI or USB connection)
Current consumption .................... 500 mA
Input.............................................. 1x HDMI
Output ........................................... 1x HDMI
...................................................... 1x Stereo analogue output (3.5 mm jack)
max. 2 channel stereo
Image resolution ........................... max. 1920x1080 @ 60 Hz
3D support .................................... yes
Compatible with ............................ HDCP 1.2
Audio sampling rate ...................... 32-192 kHz
Dimensions ................................... 60,5 x 54,5 x 20 mm
Weight .......................................... 34 g
Operating conditions ..................... 0 to +40 °C / 20-90% rel. humidity (noncondensing)
Storage conditions ........................ -20 to +60 °C / 20-90% rel. humidity (noncondensing)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2018 by Conrad Electronic SE. 1693321_V2_0818_02_m_VTP_en