Publicité
Les langues disponibles
Les langues disponibles
SAVE THESE INSTRUCTIONS!
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product replace strict
adherence to cordless product safety rules. If you use this
tool unsafely or incorrectly, you can suffer serious personal
injury.
• Hold tool by insulated gripping surfaces when performing an
operation where the accessories may contact hidden wiring .
Contact with a "live" wire will also make exposed metal parts of
the tool "live" and shock the operator .
• Be aware that this tool is always in operating condition, because it
does not have to be plugged into an electrical outlet .
• Always be sure you have firm footing .
• Be sure no one is below when using the tool in high locations .
OPERATING INSTRUCTION
Installing Or Removing Battery Pack From The Tool
1 . Your new battery pack is not fully charged . You may need to
charge before use .
2 . Make sure the forward/reverse lever is in the neutral position
when installing or removing a battery .
3 . Slide type 14 .4V, 18V, and 20V depress the front tab and pull
the battery forward and the tool in the opposite direction .
4 . Stick type 10 .8V - 16V depress 2 tabs on side and pull
battery down and out front of tool .
Charging The Battery Pack
1 . Battery may not charge when it is above a certain preset
temperature limit . Allow temperature of battery to cool before
charging .
2 . The charge process will take less than one hour .
3 . After charging, unplug the charger from the power source
and stow away in a safe place .
MCLCHRG6
MCLCHRG6 Lithium-ion Universal Battery Charger
Power On
(Green light flashes slowly)
Battery Low
(Red light stays illuminated)
Battery charged 80%
(Green light flashes rapidly)
Battery charged 100%
(Green light stays illuminated)
Battery Pack temperature is too hot
or too cold (Red light flashes slowly)
Battery Pack malfunction
(Red and Green lights stay
illuminated)
• Hold the tool firmly and use both hands .
• Keep hands and hair away from rotating parts .
• Do not leave the tool running . Do not force tool to stay in the "on"
position . Operate the tool only when hand-held .
• Do not touch the impact socket or the workpiece immediately after
operation; they may be extremely hot and could burn your skin .
• Some material contains chemicals which may be toxic . Take
caution to prevent working dust inhalation and skin contact .
Follow material supplier safety data .
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
Charger Operation
1 . Plug charge station into a 120 VAC outlet .
2 . To install stick type 10 .8V, 12V, or 16V battery align the
battery terminal ends with charger, push down until "click" is
heard . See figure 2 .
2 .
3 . To install slide type 14 .4V thru 20V batteries, slide the battery
pack into the charger as the arrow indicates . Push the
battery pack into place until click is heard . See figure 3 .
4 . Make sure the red light on the charger is "ON" . The battery
pack is now starting the charging cycle . If the battery pack is
excessively hot or cold, the charger will not begin charging
and the red indicator on the charging station will blink . When
the battery returns to between 0°C (32°F) and 50°C (122°F),
the charger will automatically begin charging . Ensure the
charging ambient temperature is between 0°C (32°F) and
40°C (104°F) .
5 . If both the red and green indicator lights are ON, the battery
pack does not comply or is defective . Please contact your
retailer .
6 . The charging process will take less than 60 minutes .
7 . Unplug the unit after the charging process and keep in a dry,
cool place .
Also available separately
RSLIBCPC, Li-ion Charger Power Cord .
3
3 .
02/14/19
Publicité
