Technical Data; Cleaning And Maintenance - physa HTS-80 Manuel D'utilisation

TECHNICAL DATA

Product name
Model
Art. No.
Rated voltage [V] / Frequency [Hz]
Temperature [°C]
Power [W]
PURPOSE
This high-temperature steriliser is a device designed for the quick sterilisation of beauty tools and accessories (such as nail
clippers, tweezers, etc.) as well as other small metal tools at high temperature. Quartz balls maintain a high temperature and
keep the tools and accessories in place during the sterilisation process.
In case of damage resulting from an improper use of the device, the user shall assume all liability.
BEFORE FIRST USE
On receipt of the parcel, make sure the packaging is undamaged before opening it. If the packaging is damaged, please contact
your transport company and distributor within 3 days. Be as specific as possible when describing the damages. Do not turn
the package upside down! When transporting the package, please ensure that it is kept horizontal and stable. The packaging
materials (cardboard, plastic straps, polyurethane foam) should be kept at hand, so that the device can be sent back to the
service center, if needed, in the best conditions!
ENVIRONMENT OF USE
The room temperature must not be higher than 45°C and the relative humidity should be under 85%. Keep the device away
from hot surfaces. Operate the device on flat, stable, clean, refractory and dry surfaces, out of the reach of children and
people with mental disabilities. Make sure that the power outlet is always within reach. The power outlet must be properly
grounded and match the technical requirements of the device.
OPERATING PRINCIPLE
6
5
4
3
2
1
CONNECTING / STARTING
Do not switch the device on if the chamber is empty – put the quartz balls inside the chamber. Make sure that the main
switch is in the OFF position. Plug the power cord into the outlet. Turn the device on with the main switch: the display shows
„8.8.", followed by „——". Press the timer button (TIMER), the display now shows „15" and the device starts its 15-minute
1
heating process. The remaining heating time is counted down on the display. Three short beeps indicate that the heating
process is over: the display shows „0.0." The steriliser is now ready for use.
Rev. IV 2016
High-temp Sterilizer
HTS-80
4101
230 V / 50 Hz
250
80
1. main switch
2. timer switch button
3. LCD display
4. sterilisation chamber
5. chamber lid
6. quartz balls
8
Place the tools / instruments among the quartz balls and press the TIMER button - this will launch a 20-second-sterilisation
cycle. A single beep indicates that the sterilisation has been completed; the display shows „0.0.". The device is ready for
the next sterilisation cycle.
The device is equipped with a safety feature interrupting heating after 8 hours of continuous use. If the interruption occurs
when the steriliser in the standby mode (STAND-BY, the display shows „0.0.") the heating will turn off, a short beep will be
heard five times and the display will show „——". If the 8-hour limit is passed during use, the heating will be interrupted
after completion of the sterilisation cycle and the display will show „0.0.".
Should you want to use the device for more than 8 hours, turn the steriliser off with the main switch and then turn it on
again. The device will need 15 minutes to warm up.
WARNING!
• Do not use the device in damp areas (such as bathrooms).
• Pre-clean the metal tools and instruments before sterilisation.
• Clean the quartz balls and the sterilisation after use.
• Do not use damaged quartz balls
TRANSPORTATION AND STORAGE
When transporting the device, avoid shaking it, dropping it and turning it upside down. Store it in a cool, dry place, free of
any corrosive gas.

CLEANING AND MAINTENANCE

• Unplug the device before cleaning.
• Use a mild, non-corrosive detergent.
• Let the device dry before using it again.
• Store the device in a dry, cool location, free from moisture and direct sunlight.
• The quartz balls can be washed in a sieve under running water with a mild detergent.
REGULAR CONTROL OF THE DEVICE
Regularly ensure that the device is in good condition. Should it be damaged, please stop using it immediately and contact
your customer service to solve the problem.
What to do in case of problem?
Please contact your customer service and prepare the following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service advisor to identify the source of the problem if you give a detailed and
precise description of the matter
The more details you give, the quicker the customer service will be able to solve your problem!
CAUTION: Never open the device without the authorization of your customer service. This may void the guarantee!
Rev. IV 2016
9 9