Parts List
Key
Part No.
Description
1
Plate, captive load ................................1
2
Sensors assembly (load and hall) .........1
3
Compressor, center loader ...................1
4
Plate, front (machined) ..........................1
5
Plate, back (machined) .........................1
6
Through pin, 1 x 0.75 x 0.5 thru ............2
7
Handle weldment ..................................2
8
SHCS, low profile, 0.375-16 x 1 ...........4
9
BHCS, threadlock, 1/4-20 x 3/4 ...........4
10
SHCS, threadlock, 6-32 x 0.5 ...............3
11
Cam locking pin, 0.750 .........................2
12
Nut, hex (1/2-13NC) ..............................2
13
BHCS, 0.5 x 13, 3.0 long ......................2
14
Set screw, 10-32 x 0.5 ..........................2
15
Screw, BHCS, 4-40 x 0.25 ....................2
16
Dowel pin, 0.250 x 2 .............................2
17
Spring, compression .............................2
18
Battery terminal assembly ....................1
Kits
Part No.
Description
52077843
Pin and removable roller kit – incudes 1 each of items 11, 14, 17, 20, 21, and 29
52078005
Locked roller and axle kit – includes 1 each of items 6, 12, 13, 27, and 30
52078007
Center roller assembly kit – includes items 3 and 15
52078008
Electronics enclosure kit – includes items 24 and 25
52079814
Battery terminal repair kit – includes item 18
52079813
Sensor repair kit – includes item 2
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Greenlee / A Textron Company
FG01 G-Series Smart Pull
Qty
Key
Part No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir
le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire
à l'établissement d'une communication satisfaisante.
11
4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
Description
SHCS, 6-32 x 1.0 ..................................4
Pin, dowel (M4 x 8MM) .........................2
Spring, compression .............................2
Screw, SSS, 1/2 x 3/4, 3/8-16 ..............1
Nut, hex, 3/8-16 ....................................2
Enclosure, electronics ...........................1
Screw, FHH, 8-32, 3/8 threadlock ........4
Link, assembly total ..............................1
Washer, flat, 0.531 ID, 1.250 OD ...........3
Decal, warning ......................................1
Roller assembly, outside .......................2
Roller assembly, secondary ..................2
Washer, flat, 0.531 ID, 1.500 OD ...........1
Wire clamp, nylon .................................1
Screw, wire clamp .................................1
Battery plate, bottom ............................1
Battery plate, top ..................................1
Qty