Publicité
Les langues disponibles
Les langues disponibles
T Television
R Radio
D Data
* Encrypted programmes have an asterisk before their
name
●
PCR PID: Program Clock Register PID. This may
be modified if necessary.
●
Video PID: Video PID. This may be modified if
necessary.
●
Audio PID: Audio PID. This may be modified if
necessary.
●
Teletext PID: Teletext PID. This may be modified if
necessary.
●
Test Settings: Press the ENTER button. If the
service can be decoded, OK will appear on
the DISAT 6 display. If the service could not
be decoded, the corresponding error message
will appear. In this case, you will need to check the
parameters programmed until you locate the error.
4. Select "Setup Modulator".
●
Output channel: Select the desired output channel.
Range of programmable channels in each module:
MODULE >1< : S09 – E12
MODULE >2< : E07 – S12
MODULE >3< : E09 – S14
MODULE >4< : E11 – S17
MODULE >5< : S11 – S26
MODULE >6< : S11 – S26
The DISAT 6 modulators are DSB (double side band),
which means that adjacent channels cannot be
programmed, and a reserve channel must always
be left between the channels programmed.
<Conflict> (x): Possible conflict between the channel
being programmed and the channel programmed on
the module (x). If this conflict is not corrected, the
image quality on these two channels will not be
optimum. You will need to select other channels to
correct the error.
●
Test Signal: To enable/disable the video test signal.
The "Test Signal" is useful if you wish to check the unit
output channels and you do not have an input satellite
signal.
●
Test Settings: Press the ENTER button to apply
the changes made. OK will appear on the
DISAT 6 display.
DEFAULT SETTINGS
Low Vertical Astra satellite frequencies:
MODULO
Satellite
Symbol TV
frequency Rate
MODULE >1< 1935 MHz 22000
MODULE >2< 1817 MHz 22000
MODULE >3< 1788 MHz 22000
MODULE >4< 1759 MHz 22000
MODULE >5< 1229 MHz 22000
MODULE >6< 1068 MHz 22000
●
"Setup SAT" _
●
FEC Rate = Auto
●
22 KHz = Disabled
●
Power LNB = Enabled
●
Polarization = Vertical
●
"Setup Modulator" _
●
Test Signal= Disabled
●
The DISAT 6's original default programming can be
restored as follows:
●
Disconnect the 230 Vac power supply and connect
it again.
●
Press the EXIT and ENTER buttons simultaneously
and hold them down while the whole start-up
process runs, until the DISAT 6 finishes checking
the 6 modules and a message appears asking you
to press the ENTER button.
●
When you press the ENTER button, the default
value recording process will start.
●
When loading is complete, the message "OK Done"
will appear.
●
Disconnect the 230 Vac power supply and connect
it again. The unit will start up with its default values.
SAFETY INSTRUCTIONS
●
We have taken all possible steps to guarantee that
the information in this manual is accurate and detailed.
However, Fagor Electrónica will not be liable for any
errors or omissions that may be contained in it.
●
Fagor Electrónica reserves the right to change the
hardware and software specifications described in
this manual without prior notice.
●
The total or partial reproduction of this manual is
prohibited, as is its translation or storage in information
retrieval systems without previous written authorisation
from Fagor Electrónica.
●
Fagor Electrónica assumes no liability for any damages
caused due to damaged or lost data resulting from
the improper operation or incorrect functioning of the unit
or the software, or the use of peripherals and power
sources not authorised by Fagor Electrónica.
11
Output
Output
Programme channel
channel
(DISAT 6V) (DISAT 6U)
TVC INT
E06
CH21
TVEi
E08
CH23
Telesur
E10
CH25
Extremadura
E12
CH27
TV
TV Canaria
S12
CH29
TVVI
S14
CH31
Publicité
