Publicité
12
| English
Vibration total values a
and uncertainty K determined according to
EN 62841-1, EN 62841-2-17
Vibration level max:
a
h
K
IDENTIFICATION
1. Routing motor
2. Plunge base
3. Βrush cover
4. Handle (insulated gripping surface)
5. Adjustment knob for fine adjustment of
depth-of-cut (plunge base)
6. Cable
7. Release lever for plunge action
8. Scale for depth-of-cut adjustment (plunge
base)
9. Slide with index mark (plunge base)
10. Depth stop (plunge base)
11. Turret stop
12. Base plate
13. Guide plate
14. Thumbwheel for speed preselection
15. Knurled screw for depth stop (plunge base)
16. Tightening nut with collet
17. Lock-on button for On/Off switch
18. On/Off switch
19. Seat for parallel guide rods
20. Spindle lock button
21. Open-end spanner, size 24mm
22. Extraction adapter
23. Intermediate ring for extraction adapter
24. Parallel guide
25. Wing bolt for coarse adjustment of parallel
guide
26. Fine-adjustment knob for parallel guide
27. Adjustable edge guide for parallel guide
28. Wing bolt for guide rods of parallel guide (2x)
29. Router compass/guide-rail adapter
30. Wing bolt for fine adjustment of router com-
pass (1x)
31. Fastening screw for guide bushing adapter
(2x)
32. Guide bushing
33. Plastic guard
34. Fastening screw for plastic guard
ASSEMBLY
Before any work on the machine itself,
pull the mains plug.
INSERTING A ROUTER BIT (Ι,J)
It is recommended to wear protective
gloves when inserting or replacing rout-
er bits.
Depending on the application, router bits are
available in the most different designs and qual-
ities.
Router bits made of high speed steel are suit-
(triax vector sum)
h
m/s
7,78
2
m/s
1,5
2
able for the machining of soft materials, e.g. soft-
wood and plastic.
Carbide tipped router bits are particularly suit-
able for hard and abrasive materials, e.g. hard-
wood and aluminium.
Use router bits with a shank diameter of 12 mm
as far as this is possible. Only use clean router bits
that are in perfect condition.
Press and hold the spindle lock button (20). If re-
ƒ
quired, turn the spindle by hand until the lock
engages.
Actuate the spindle lock button (20) only
when at a standstill.
Loosen the tightening nut (16) with the open-end
ƒ
spanner (21) (size 24 mm) by turning in antclock-
wise direction.
Insert the router bit into the collet. The shank of
ƒ
the router bit must be immersed at least 20 mm
into the collet.
Tighten the tightening nut (16) with the open-end
ƒ
spanner (21) (size 24mm) by turning in clockwise
direction. Release the spindle lock button (20).
Do not insert a router bit with a diameter larg-
f
er than 50mm when the guide bushing is not
mounted. Such router bits do not fit through the
base plate.
Do not tighten the tightening nut of the collet
f
without a router bit inserted. Otherwise the collet
can be damaged.
DUST/CHIP EXTRACTION
Dusts from materials such as lead-containing coat-
f
ings, some wood types, minerals and metal can be
harmful to one's health. Touching or breathing-in
the dusts can cause allergic reactions and/or lead to
respiratory infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are con-
sidered as carcinogenic, especially in connection
with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may
only be worked by specialists.
As far as possible, use a dust extraction system
ƒ
suitable bfor the material.
Provide for good ventilation of the working place.
ƒ
It is recommended to wear a P2 filter-class respi-
ƒ
rator.
Observe the relevant regulations in your country
for the materials to be worked.
Prevent dust accumulation at the workplace.
f
Dusts can easily ignite.
OPERATION
STARTING OPERATION
Observe correct mains voltage! The
voltage of the power source must
agree with the voltage specified on the
nameplate of the machine. Power tools
marked with 230 V can also be operated
with 220 V.
PRESELECTING THE SPEED (C)
The required speed can be preselected with the
thumbwheel (14) (also while running).
1-2 low speed
RO 1600 PLUS
Publicité
