Publicité
Les langues disponibles
Les langues disponibles
8
| English
Weight (drill & battery)
Protection class
Sound emission values determined according
to EN 60745-1
Typically the A-weighted noise levels of the product
are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a
and uncertainty K determined according to
EN 60745-1
Vibration Level
a
h
K
Battery:
Type
Voltage
Rating
Charger:
Rated Voltage
Rated Frequency
Rated D.C. Output
Voltage
Rated D.C. Output
Current
IDENTIFICATION
1. Torque selector
2. DC-Connector
3. Changeover switch
4. ON/OFF switch
5. Quick-change drill chuck
6. Battery charger
7. LED lamp
8. Charging indicator
9. Hanging belt
BEFORE STARTING THE EQUIPMENT
Be sure to read the following information before you
use your cordless drill for the first time:
1. Charging the device with the charger supplied.
An empty battery requires a charging period of
approximately 5 hours.
2. Only ever use sharp drill bits and screwdriver bits
which are suitable for the purpose and in faultless
condition.
3. Always check for concealed electric cables and
gas and water pipes when drilling and screwing
in walls.
Kg
0,71
/ II
dB(A)
68,7
dB(A)
79,7
dB
3
(triax vector sum)
h
m/s
1,29
2
m/s
1,5
2
Li-Ion
V
7,2
Ah
1,5
V
100-240
Hz
50/60
V
9,6
A
0,3
OPERATION
CHARGING THE BATTERY (image 2)
1. Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the mains plug of the charger (6) into the
mains socket outlet.
2. Push the DC-Connector into the device as image
2 showed. When the charging process is finished,
the red LED will extinguish. The time it takes to
fully recharge an empty battery is approximately
5 hours.
3. The temperature of the battery may rise slightly
during the charging operation. This is normal. If
the green LED extinguishes during charging, the
temperature is either above or below the perfect
charging temperature. In this case, pull the plug of
the charger and charge the battery in an environ-
ment in which the temperature is either warmer
or colder.
If the battery fails to become charged, please
check
• whether there is voltage at the socket-outlet
• whether there is proper contact at the charging
contacts on the charger.
If the battery still fails to become charged, please re-
turn
• the charger to our Customer Service Department.
To ensure that the battery provides long service
you should take care to recharge it promptly. You
must recharge the device when you notice that the
power of the cordless drill drops. Never fully dis-
charge the device. This will cause the battery pack
to develop a defect.
TORQUE SETTING (IMAGE 3 / ELEMENT 1)
The cordless drill is fitted with a mechanical torque
selector. The torque for a specific size of screw is
selected with the set-collar (1). The correct torque
depends on several factors:
• on the type and hardness of material be drilled
• on the type and length drill bits used
• on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to indi-
cate when the set torque is reached.
Important! The tool must be at a standstill when you
set the torque with the setting ring.
DRILLING (image 4 / element 1)
For drilling purposes, move the set-collar to the last
step "Drill"
. In this setting the slip clutch is inac-
tive.
The maximum torque is available in drilling mode.
FORWARD / REVERSE SWITCH (image 5 / element 3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery
powered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To
avoid causing damage to the gearing it is advisable
to change the direction of rotation only when the
tool is at a standstill. The On/Off switch is blocked
when the slide switch is in center position.
CDD 7.2V EASY
Publicité
