Power Stroke PSL1QS01 Manuel D'utilisation page 9

PAPER PUNCH
See Figure 4, page 12.
A paper punch template has been supplied with the sander.
It should be used for aligning and punching holes in the
sandpaper for alignment with the holes in the cushion.
Punching the holes properly is a necessary step in order
for the dustless feature of the sander to function properly.
 Install sandpaper on the sander.
 Align sander cushion to paper punch as shown by the
icon on the paper punch template.
 Push down on sander.
DUSTLESS SANDING
See Figures 5 - 6, page 12.
WARNING:
Do not use the dust bag when sanding metal. Using the
dust bag when sanding metal creates a fire hazard, which
could damage the tool and lead to serious personal injury.
ATTACHING THE DUST BAG ASSEMBLY
See Figure 5, page 12.
The dust bag assembly provides a dust collection system
for the sander. Sanding dust is drawn up through the holes
of the sanding disc to collect in the dust bag during sand-
ing operation.
 Unplug the sander.
 Slide the dust bag assembly onto the blower exhaust
on the sander using a twisting motion.
NOTE: For more efficient operation, empty dust bag when
no more than half full. This will permit the air to flow through
the bag better.
WARNING:
Collected sanding dust from sanding surface coatings
such as polyurethanes, linseed oil, etc., can self-ignite
in the sander dust bag or elsewhere and cause fire. To
reduce the risk of fire, always empty the dust bag fre-
quently while sanding. Never store or leave a sander
without totally emptying its dust bag (see Cleaning the
Dust Bag Assembly). Also follow the recommendations
of the coatings manufacturers.
TO CONNECT VACUUM HOSE
See Figure 6, page 12.
When sanding for an extended period of time, you can easily
attach the dust exhaust of the sander to a vacuum.
To attach:
 Unplug the sander.
 Remove dust bag from sander.
OPERATION
 Attach vacuum hose to dust exhaust.
NOTE: Vacuum hose fits inside dust exhaust.
 Connect sander and vacuum to power supply.
WARNING:
When sander is not connected to vacuum, always install
dust bag back on sander. Failure to do so could cause
sanding dust or foreign objects to be thrown into the
face or eyes which could result in possible serious injury.
OPERATING THE SANDER
See Figure 7 - 8, page 12.
Clamp or otherwise secure the work to prevent it from
moving under the sander.
WARNING:
Unsecured work could be thrown towards the operator
causing injury.
Hold the sander in front and away from you, keeping it clear
of the workpiece. Start the sander by sliding the switch to
the ON ( I ) position and letting the motor build to its maxi-
mum speed. Gradually lower the sander on the work with a
slight forward movement. Move it slowly using forward and
backward strokes.
Do not force. The weight of the unit supplies adequate
pressure, so let the sanding sheet and sander do the work.
Applying additional pressure only slows the motor, rapidly
wears sandpaper and greatly reduces sander speed. Ex-
cessive pressure will overload the motor causing possible
damage from motor overheating and can result in inferior
work. Any finish on resin or wood may soften from the fric-
tional heat. Do not allow sanding on one spot too long as the
sander's rapid action may remove too much material, making
the surface uneven. Always lift the sander from workpiece
before turning off.
Flush sanding can be performed with the sander. The front
edge of the sander allows flush sanding in corners. Always
remove sander from workpiece before turning the sander off.
ORBITAL MOTION
Orbital motion is ideal for fast cutting action when removing
old finishes, smoothing rough wood, cutting stock down to
required dimensions or for finishing surfaces to be painted.
The sandpaper moves in tiny circles at a very high speed,
allowing the sander to move easily.
9 - English