Sander Safety Warnings - Power Stroke PSL1OS01 Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

GeNerAL PoWer tooL sAFetY WArNiNGs
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation
 tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
 Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live"
and shock the operator.
 Know your power tool. read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
power tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
 Always wear eye protection with side shields marked
to comply with ANsi Z87.1. Failure to do so could
result in objects being thrown into your eyes, resulting in
possible serious injury.
 Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
 Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
 inspect power tool cords periodically and, if damaged,
have repaired at your nearest Authorized service
Center. Constantly stay aware of cord location.
Following this rule will reduce the risk of electric shock
or fire.
 Check damaged parts. Before further use of the power
tool, a guard or other part that is damaged should be
CALiForNiA ProPositioN 65
WArNiNG!
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may
contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products and,
• arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.

sANDer sAFetY WArNiNGs

Page 4 - English
serviCe
 Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
 When servicing a power tool, use only identical
replacement parts. Follow instructions in the
maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
 make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product
will draw. A wire gauge size (A.W.G.) of at least
16 is recommended for an extension cord 50 feet
or less in length. A cord exceeding 100 feet is not
recommended. if in doubt, use the next heavier gauge.
the smaller the gauge number, the heavier the cord.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
 inspect for and remove all nails from lumber before
using this power tool. Following this rule will reduce the
risk of serious personal injury.
 if the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk.
 save these instructions. Refer to them frequently and
use them to instruct others who may use this power tool.
If you loan someone this power tool, loan them these
instructions also.

Publicité

Table des Matières
loading

Table des Matières