BASETech 1168631 Mode D'emploi page 6

• The two slots (1) are intended for the sharpening of knives. The long slot (2) is used for the
sharpening of scissors.
Sharpening corrugated or serrated knives/scissors is not possible as they will be
damaged and become unusable!
• When you switch on the sharpener (switch position "I"), the grinding wheel will start to rotate.
After a few seconds the device will reach the normal number of revolutions.
• When sharpening knives, press them only slightly onto the grinding wheel. Do not apply
strong pressure or force.
Depending on the blade type, the knife is to be sharpened on the left, on the right or on both
sides. Start near the handle piece and pull the blade towards yourself (2a, 2b, 2c).
• When sharpening scissors, open the scissors, and depending on the design of the scissors,
move one or both blades one after another over the grinding wheel.
Do not apply strong pressure or force. Always move the blade over the grinding wheel start-
ing from the joint to the tip (2d, 2e, 2f).
• If you do not wish to grind another knife or pair of scissors, switch the sharpener off (switch
position "O"). Wait until the grinding wheel has come to a complete standstill.
Sharpening drill bits
Important!
Please consult the chapter "Safety Instructions"!
• Install the respective insert correctly. For this purpose, observe the chapter "Description of
the inserts" and "Attaching/replacing an insert".
• Remove the drill holder (1) from the insert.
• Unfasten the locking wheel of the drill holder and insert a spiral drill bit (2) into the opening of
the drill holder, as shown in the picture.
• Fasten the locking wheel slightly so that the drill bit does not jiggle but can still be moved (1a).
• Insert the drill holder into the adjustment slot of the insert as shown in the picture (1b).
• Move the drill bit so that the tip touches the metal stop in the slot (1b).
• Push the V-insert (3) in the direction of the drill bit and carefully turn the drill bit back and
forth until the V-insert can be pushed as far down possible (1c) and the tip of the drill bit still
touches the metal stop.
• Now tighten the locking ring so that the drill bit can no longer move.
• Pull the V-insert back slightly and remove the drill holder with the fastened drill bit.
• When you switch on the sharpening device (switch position "I"), the grinding wheel will start
to rotate. After a few seconds the device will reach the normal number of revolutions.
• Insert the drill holder in the grinding bracket of the insert (1e) and lightly hold the drill holder.
Do not press the drill bit onto the grinding surface too strongly, otherwise this will
have a negative effect on the grinding result!
• Move the swivel grinding table of the insert to the left and right (1f, see arrow imprint on the
insert).
• Remove the drill holder from the drill bracket and turn it 180° in order to grind the second drill
bit in the same way (1g).
Both sides of the drill bit must be ground evenly (1h), as an incorrectly ground drill
bit (1i) will not be able to drill a hole neatly.
• After grinding and removing the drill bit, the sharpener must be switched off (switch position
"O"). Wait until the grinding wheel has come to a complete standstill.
• If you wish to grind another drill bit, proceed as described above.
Maintenance and Cleaning
• The product is maintenance-free for you; never dismantle it (except for the tasks necessary
for replacing the inserts or grinding as described in these operating instructions).
• Switch off the product and disconnect it from the mains voltage before cleaning it. Then wait
until the grinding wheel has come to a complete standstill.
• The outside of the product should only be cleaned with a clean, soft, dry cloth.
Do not use aggressive cleaning agents or chemical solutions that could damage the housing
(discolouring) or impair operation.
• Dust can be easily removed with a brush and a vacuum cleaner, if necessary.
Disposal
Electrical and electronic devices must not be disposed of as domestic waste!
Please dispose of the product when it is no longer in use, in accordance with current
statutory requirements.
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and other relevant regulations of the machi-
nery directive 2006/42/EC.
You can find the conformity declaration for this product at www.conrad.com
Technical Data
Operating voltage ........................................ 230 V/AC, 50 Hz
Power consumption ..................................... Max. 65 W
Protection class ........................................... II
Cable length ................................................ approx. 1.8 m
Grinding wheel diameter .............................. 50 mm
Number of revolutions of grinding wheel ...... 6700 rpm
Drill bit diameter ........................................... 3 - 10 mm (only drills with 2 bits)
Drill bit angle ................................................ 118°
Width of ripping chisel/chisel ....................... 6 - 51 mm
Operating time ............................................. 20 minutes, afterwards let the device cool down for
Ambient conditions ...................................... Temperature: -10 °C to +40 °C
.....................................................................
Dimensions .................................................. 190 x 185 x 160 mm
Weight ......................................................... 1.52 kg
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
at least 20 minutes before using it again
Air humidity: 0% to 85% relative, non-condensing