Publicité
Les langues disponibles
Les langues disponibles
Programming a receiver
• First, move the slide switch for the learning code (see
circle in the picture) to the position "Learning Code".
This should be pre-set already in the basic setting of
the motion detector.
☞
The other 3 switch positions are not needed.
• Insert 2 type AAA/micro batteries, if not already done.
• Then initiate the learning mode, starting with the
receiver that should learn the motion (e.g., for a wire-
less switch socket press the button "Learning Code"
until the LED on the button starts flashing).
• Now, for example, using a toothpick, press the but-
ton „Learning" on the motion sensor (see arrow in the
picture) for about 2-3 seconds.
The LED on the receiver (e.g., a wireless socket switch) will go out, which indicates that the
radio signal of the motion sensor has been detected and has learned that now.
☞
If the receiver does not recognize the motion detector, check whether the batteries
in the motion sensor are inserted correctly. Make sure that the receiver is in learning
mode, while holding down the button "Learning" on the motion sensor.
• If the motion sensor is for instance is intended to control a further (second, third.....) wireless
socket switches, please repeat the steps described above. That way the motion sensor can
activate several RSL receivers.
Limiting the motion detection range
The movement detection range can be limited with the diffuser lens included in the delivery.
The cover can be fitted e.g. with scissors. Then the diffuser lens cover is attached to the dif-
fuser lens.
Maintenance and care
The product does not require any maintenance and should never be opened or disassembled
for any reason.
Clean the product with a soft, clean and dry cloth. Never use aggressive cleaning agents or
chemical solutions since these might damage the surface of the casing or impair the operation.
Handling
• The wireless motion detector must not get damp or wet.
• Avoid the following unfavourable environmental conditions in the during use and
during transportation:
- Humidity and dampness may cause damage to the motion detector.
- Direct sunlight
- Extreme cold or heat
- Dust or flammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
• Ensure that the enclosure of the entire product is neither damaged nor destroyed.
Never disassemble the product! Except for changing the battery, there are no serv-
iceable parts inside.
• Check the product for damage before use!
If you notice any damage, do not use the product any longer!
Safe operation must be presumed to be no longer possible:
- if the device is visibly damaged
- if the device no longer works
- if the device was stored under unfavourable conditions for a long period of time
- the device was exposed to extraordinary stress caused by transport.
Transmission range
The transmission range of the radio signals between the wireless motion detector and the cor-
responding receiver is up to 70m under optimum conditions.
☞
This value, however, is the so-called "open space range" (the range the transmitter
and receiver are visible to each other, without interfering influences).
In practical operation, however, there are walls, ceilings of rooms etc. between the
transmitter and the receiver, which reduce the range accordingly.
Due to the different influences on the radio transmission, no specific range can be
guaranteed.
However, trouble-free operation is usually possible in a detached house.
The coverage can partly be limited considerably by:
• walls, reinforced concrete ceilings
• coated/metallised insulated glass
• proximity to metal & conducting objects (e.g. radiators)
• proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-
controlled headphones, radio-controlled speakers, radio-controlled weather stations, baby
phones etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• The proximity to improperly shielded or uncovered operating computers or other electric ap-
pliances
Disposal
a) General
Electrical and electronic products do not belong in the household waste!
Please dispose of the device when it is no longer of use, according to the current
statutory requirements. Remove any inserted batteries and dispose of them sepa-
rately from the product.
b) Batteries and rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return all used batteries/
rechargeable batteries; disposal of them in the household waste is prohibited!
Contaminated batteries/rechargeable batteries are labelled with the symbol to indi-
cate that disposal in the domestic waste is forbidden. The designations for the heavy
metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
You can return used batteries/rechargeable batteries and button cells free of charge
to any authorised disposal station in your area, to our stores or to any other store
where batteries/storage batteries/button cells are sold.
Thus you fulfil the legal requirements and contribute to protecting the environment!.
Declaration of conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that the
product conforms to the fundamental requirements and the other relevant regulations of
Directive 1999/5/EC.
☞
The Declaration of Conformity for this product can be found at www.conrad.com.
Technical data
Transmission frequency: ........433 MHz
Power supply: ........................2 x 1.5 V micro batteries (type: AAA).
Range: ...................................up to 30 metres (open space, see chapter "Transmission range")
Motion detection angle: .........90° (horizontal)
Detection range: ....................up to 8 metres
Operating temperature: .........0 °C to +35°C
Weight without batteries: .......approx. 56 g
Dimensions (L x W x H): ........approx. 80 x 80 x 28 mm
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
Publicité
