Publicité
Les langues disponibles
Les langues disponibles
G
O P E R A T I N G I N S T R U C T I O N S
Wireless Motion Detector RSL
Item no. 75 19 01
Intended use
This wireless motion detector serves to switch a corresponding receiver (e.g. wireless power
socket, wireless external power socket switch, etc.) on or off. The mount dimmer has a hori-
zontal movement detection range of 90° (max. detection range up to 8 metres). The movement
detection range can be limited with the diffuser lens included in the delivery. Moreover, the
activation duration upon movement detection (6 s, 15 s, 1 min, 5 min) and the brightness
sensitivity can be adjusted.
The wireless motion detector is only intended for use in dry indoor locations.
It is powered by 2 x 1.5 V micro batteries (type: AAA).
All the safety and operating instructions in this manual must be followed carefully. These in-
structions not only protect the device but, in particular, your health. Please read the entire
operating manual before using the product.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner.
All rights reserved.
Safety instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions. We do not assume any liability for any consequen-
tial damage!
Nor do we assume liability for damage to property or personal injury caused
by improper use or failure to observe the safety instructions. The warranty will
be null and void in such cases.
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE).
• Do not use this product in hospitals or medical institutions. Although the product
emits only relatively weak radio signals, these may lead to the malfunction of life-
support systems. The same may possibly be the case in other areas.
• The wireless motion detector is powered by 2 x 1.5 V micro batteries (type: AAA).
• The product is not a toy and must be kept out of the reach of children. Therefore,
be especially careful when children are around.
• Never expose the motion detector to extremely high or extremely low tempera-
tures, humidity or vibrations.
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
Battery notes
• Batteries should be kept out of the reach of children.
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by
children or domestic animals. If swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Make sure that batteries is neither short-circuited nor thrown into a fire. There is a risk of
explosion!
• Do not recharge normal batteries. There is a risk of explosion! Only charge rechargeable bat-
teries that are intended for this purpose; use a suitable battery charger.
• Remove the batteries when not in use over long periods (e.g., storage). Aging batteries may
leak, which might cause damage to the product and loss of guarantee/warranty!
• For environment friendly disposal of batteries and rechargeable batteries, please read the
chapter "Disposal".
• Because rechargeable batteries have a lower voltage (rechargeable battery = 1.2 V battery =
1.5 V), we recommend using high-quality alkaline batteries for the wireless motion sensor to
ensure long and safe operation.
Description of functions
www.conrad.com
This motion detector responds to heat radiation, which is emitted by objects entering the detec-
tion area of the motion detector. The motion detector must "see" the area it is to keep under sur-
Version 12/13
veillance. Heat radiation travels in straight lines but is obstructed, for example, by glass or other
fixed objects. Before mounting, therefore, pay attention to this, or other problem sources. If the
detection area of the motion detector is entered, the programmed receiver (e.g. wireless power
socket) is activated. The activation duration can be adjusted at the motion detector. In addi-
tion, the ambient brightness, at which the motion detector shall be activated, can be adjusted.
Installation
☞
Proceed as follows, to ensure the correct installation:
• Use a flat screw driver to remove the front plate with the diffuser lens.
• The mounting plate at the back has two mounting holes. Take the mounting plate and indicate
the mounting holes at the intended mounting position.
• Drill the holes.
• Fix the mounting plate with suitable installation material.
• Insert the electronic component into the mounting plate.
• Attach the front plate with the diffuser lens (so that it engages).
Timer and brightness setup
The motion detector has two sliding switches for adjustment of activation duration and bright-
ness sensitivity.
Slide switch for activation duration:
Explanation:
6 s: Activation duration of 6 seconds
15 s: Activation duration of 15 seconds
1 m: Activation duration of 1 minute
5 m: Activation duration of 5 minutes
Inserting/replacing the batteries
• Use a flat screw driver to remove the front plate with the diffuser lens.
• Remove the used batteries, if necessary.
• Insert 2 x 1.5 V micro batteries observing the correct polarity (Type: AAA) into the battery
compartment.
• Attach the front plate with the diffuser lens (so that it engages).
When selecting the position for installing the motion detector, please note that it
must not be subjected to direct sunlight, humidity, vibrations, dust, heat or cold. This
can lead to faulty activation, defects or functional impairment.
The motion detector is only suitable for use in dry, closed indoor locations.
Do not place devices with strong magnetic or electric fields, such as mobile phones,
electric motors, etc. in the immediate vicinity.
Recommended installation height: 1 to 1.5 metres
To ensure optimal motion detection, the motion detector must be placed so that the
object to be detected does not approach the motion detector directly but passes
from left to right or vice versa.
Slide switch: brightness sensitivity:
Explanation:
The closer the sliding switch is positioned to
the sun symbol, the brighter the ambient area
upon activation due to motion detection.
Publicité
