Publicité
Les langues disponibles
Les langues disponibles
340-00050 / 340-00051
Read the complete manual before carrying out the installation and activating the system.
1. DESCRIPTION
The power supplies are suitable for powering LEDs and are designed for DIN rail mounting. The 24 Vdc output
voltage is stable with a narrow tolerance, small ripple and high efficiency. The output power range is adjustable
(see technical data).
The total connected load can be a maximum of 60 W (340-00050) or 100 W (340-00051). A blue LED on the
power supply unit indicates whether the unit is correctly connected and whether 24 Vdc is available.
The power supplies are equipped with an input-surge current limiter. They are protected against overloading,
overvoltage, overheating and short circuiting. The power supplies comply with the safety standard (EN 61558-1) and
the EMC standards (EN 61558-2-16; EN 55032 Class B; EN55024; EN 61000-3-2, EN 61000-3-3).
2. MOUNTING AND CONNECTIONS
The DIN rail power supplies have 2 outputs to which LEDs can be connected.
The power supply has a width of 3U (60 W version) or 4U (100 W version) and can be placed in a DIN rail cabinet.
The load must be connected between the connection terminals '+' and '-' (see fig. 1).
Fig. 1A Wiring diagram 60 W (340-00050) DIN rail LED power supply;
Fig. 1B Wiring diagram 100 W (340-00051) DIN-rail LED power supply
Mounting recommendations:
- If you place various modules alongside each other, be sure to leave sufficient space in-between to allow good
ventilation and cooling of the module: keep 5 mm free on the left and right sides and 10 mm at the bottom. If
the nearby product happens to be a heat source, leave 10 to 15 cm between both modules.
- Always mount the power supply vertically with the input at the bottom and the outputs at the top. No other
mounting direction is permitted.
- Place the power supplies preferably at the bottom of the distribution cabinet.
- Check the temperature. If the temperature in the distribution cabinet rises too high (max. 45 °C), make sure
to provide additional ventilation to guarantee an optimal life span. Provide sufficient space at the top of the
board. Place a ventilator if necessary.
- In case of high temperatures, take the following power consumption graphs into account (fig. 2a and 2b).
- For 340-00051: if the ambient temperature is higher than 35 °C, the product must be connected with wiring
that is resistant to a minimum of 80 °C.
- Try to spread the load of the power supply across the various connection terminals '+' and '-' to distribute
the current and thermal tensions across the connection terminals.
Fig. 2A Power consumption graph 340-00050
Fig. 2B Power consumption graph 340-00051
3. TECHNICAL DATA
340-00050: DIN rail LED power supply 60W
In general:
- Mounting: .............................................. DIN rail (3E)
- Dimensions: ...........................................W52.5 x H90 x D55 mm
- Weight: ..................................................±190 g
- Efficiency: ..............................................90 %
- Operating temperature: ...........................-20 °C – +60 °C (see power consumption graph fig. 2a)
- Ambient temperature: ............................. Ta 45 °C
- Stocking temperature & humidity: ............-40 °C – +85 °C; 10 – 95 % RH (non-condensing)
- Protection against short-circuit, overvoltage and overload (self-resetting).
- Designed for use in an environment with non-condensing humidity (20% - 90% RH)
- Maximum number of modules connected to a 16 A fuse: 7 items
- Recommended strip length of wiring: .......6 mm
- Recommended screwdriver: ....................flat 3 mm
Input:
- Input terminals (1 pair): ...........................2 x 1.5 mm
- Power supply voltage: .............................100 ~ 240V~; frequency 50 ~ 60Hz
- Input current: .........................................0.8 A/230 V~; 1.2 A/115 V~
- Inrush current: ........................................cold start: 60 A/230 V~; 30 A/115 V~
- Recommended screw coupler: ...............33 Ncm
Outputs:
- Output terminals (2 pairs): .......................2 x 1.5 mm
- Adjustable output voltage range: ..............21.6V DC – 29V DC
- Nominal current/power: ..........................2.5 A / 60 W
- Voltage stability: .....................................± 1%
- Ripple: ...................................................150 mVp-p
- Max. voltage disruption: ..........................30 ms/230 V~; 12 ms/115 V~
- Recommended screw coupler: ................49 Ncm
- SELV
340-00051: DIN rail LED power supply 100W
In general:
- Mounting: .............................................. DIN rail (4E)
- Dimensions: ...........................................W70 x H90 x D55 mm
- Weight: ..................................................±250 g
- Efficiency: ..............................................90 %
- Operating temperature: ...........................-20 °C – +60 °C (see power consumption graph fig. 2a)
- Ambient temperature: .............................Ta 40 °C
- Stocking temperature & humidity: ............-40 °C – +85 °C; 10 – 95 % RH (non-condensing)
- Protection against short-circuit, overvoltage, overheating and overload (self-resetting).
- Designed for use in an environment with non-condensing humidity (20% - 90% RH)
- Maximum number of modules connected to a 16 A fuse: 7 items
- Recommended strip length of wiring: .......6 mm
- Recommended screwdriver: ....................flat 3 mm
nv Niko sa
or 1 x 2.5 mm
2
2
or 1 x 2.5 mm
2
2
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.eu — www.niko.eu
Input:
- Input terminals (1 pair): ...........................2 x 1.5 mm
- Power supply voltage: .............................100 ~ 240 V~; frequency 50 ~ 60Hz
- Input current: .........................................1.6 A/230 V~; 1.2 A/115 V~
- Inrush current: ........................................cold start: 70 A/230 V~; 35 A/115 V~
- Recommended screw coupler: ................33 Ncm
Outputs:
- Output terminals (2 pairs): .......................2 x 1.5 mm
- Adjustable output voltage range: ..............21.6 V DC – 29 V DC
- Nominal current/power: ..........................4.2 A / 100.8 W
- Voltage stability: .....................................± 1 %
- Ripple: ...................................................150 mVp-p
- Max. voltage disruption: ..........................30 ms/230 V~; 15 ms/115 V~
- Recommended screw coupler: ................49 Ncm
- SELV
4. EC MARKING
This product complies with all of the relevant European guidelines and regulations. For radio equipment
Niko nv declares that the radio equipment in this manual conforms with the 2014/53/EU directive. If
applicable, the full text of the EU Declaration of Conformity can be found on www.niko.eu.
5. WARNINGS REGARDING INSTALLATION
The installation of products that will permanently be part of the electrical installation and which include dangerous
voltages, should be carried out by a qualified installer and in accordance with the applicable regulations.
This user manual must be presented to the user. It should be included in the electrical installation file and it should
be passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.
6. ENVIRONMENT
This product and/or the batteries provided cannot be deposited in non-recyclable waste. Take your
discarded product to a recognised collection point. Just like producers and importers, you too play an
important role in the promotion of sorting, recycling and reuse of discarded electrical and electronic
equipment. To finance the rubbish collection and waste treatment, the government levies recycling
charges in certain cases (included in the price of this product).
7. NIKO CUSTOMER SERVICES
Do you have a question or is the product faulty? Contact your wholesaler or Niko customer services (Belgium:
+32 3 778 90 80) or consult the 'Help and Advice' section on www.niko.eu.
8. DISCLAIMER
Niko prepares its manuals with the greatest care and strives to make them as complete, correct and up-to-date
as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than
within the legal limits. Please inform us of any deficiencies in the manuals by contacting Niko customer services
at support@niko.eu.
POWER SUPPLY
24V - 60W
INPUT: 100-240V 1,8A 50/60Hz
λ 0,45
OUTPUT: 24V
2,5A 60W
ta 45°C
INDUSTRIEPARK WEST 40
BE - 9100 SINT-NIKLAAS
L
N
340-00050
N
230V~
L
340-00050
Fig. 1A
100
90
80
70
60
50
40
340-00050
30
20
10
-20 -10 0
10
20
30
40
50
60
AMBIENT TEMPERATURE (°C)
Fig. 2A
or 1 x 2.5 mm
2
2
or 1 x 2.5 mm
2
2
POWER SUPPLY
24V - 100W
INPUT: 100-240V 3,0A 50/60Hz
OUTPUT: 24V
4,2A 100,8W
INDUSTRIEPARK WEST 40
BE - 9100 SINT-NIKLAAS
L
N
340-00051
N
230V~
L
340-00051
Fig. 1B
100
90
80
110VAC
70
input
60
50
40
340-00051
30
20
10
-20 -10 0
10
20
30
40
50
70
(vertical)
AMBIENT TEMPERATURE (°C)
Fig. 2B
λ 0,45
ta 40°C
230VAC
input
60
70
(vertical)
PM340-0005XR18034
Publicité
