Sigel Artverum Instructions De Montage Et De Sécurité page 5

GB
MOUNTING INSTRUCTIONS
1 // Before mounting, check that there are no service pipes, e.g. for electricity, gas or water, in that part of the wall.
2 // When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such as stone
or tiles. We cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be mounted and do not
remove the protective corners until it is attached to the wall.
3 // The magnetic glass board should only be mounted on an even, solid wall.
4 // Two people are required to mount the board.
5 // In order to mount our magnetic glass boards correctly, we recommend using the enclosed drilling templates. You will find the measurements
for the relevant distances between drill holes on page 10 and on our website at www.sigel.co.uk/mounting
MOUNTING
1 // The magnetic glass board can be mounted in portrait or landscape format. The enclosed drilling templates make it simple to mark the position
of the drill holes. The wall fixings d are screwed securely to the wall using anchors b and screws c . The side of the board with the Sigel logo
should be facing outwards (fig. I).
Tip: Please use a spirit level to check that the wall fixings d are lined up straight.
The wall fixings d have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the wall fixings
d vertically or horizontally as required. Then tighten the screw again.
2 // Two people are required to mount the magnetic glass board. An additional handle f for each person is included for the boards in the 150x100
cm, 180x120 cm and 240x120 cm formats.
Tip: to simplify the positioning of the board, mark the wall lightly in pencil (fig. II), e.g. to indicate the width of the board. Likewise, you can mark the position
of the corners and the mounting fittings (for distances see pg. 6).
To mount the board on the wall, hold the bottom edge with one hand and the side with the other. If mounting one of the large boards, use the
handle f to support the bottom edge (Fig. III) and grip the side of the board firmly with your other hand. The magnetic glass board a is then
mounted onto the wall fixings d (fig. IV). There are four or six mounting fittings e on the back of the board for this. Each mounting fitting e
has two openings (fig. V); the wall fixings d must always be slotted into the top opening rather than the side opening, whether the board is hung
in portrait or landscape format. Place the mounting fittings e on the back of the board over the wall fixings d so that the wall fixings d are in
the centre (fig. V). Now slide the board downwards so that the wall fixings d click into the mounting fittings e (fig. VI) and the board is mounted
securely.
Make sure that the magnetic glass board is mounted on all fittings and check that the board is securely in place before letting go. Silicon pads on
the back of the board keep it steady while it is being written on.
MOUNTING SEVERAL BOARDS IN A ROW
Please note the following if mounting several boards next to each other:
Due to the fragile glass edges, the magnetic glass boards should not be mounted right next to each other. There should be a gap of at least 3 mm
between the individual boards. When mounting the boards, make sure the edges do not knock against each other, as this can cause the board to
break. Sigel is not liable for any damage caused in this way. Do not remove the edge protector or the protective corners until the mounting process
is complete.
Mount the first magnetic glass board as described under "Mounting" before marking the drill holes for the next board. This will allow you to adjust
the position of the additional boards to any slight inaccuracies there may be in the position of the first board.
SAFETY PRECAUTIONS
The artverum® Magnetic Glass Board is made of tempered safety glass tested to EN 12150-1.
The glass surface should be written on using only special markers for glass. The magnetic glass board can be cleaned with a damp or dry cloth.
Please do not use abrasive scouring agents, detergents or chemicals to clean the board. To prolong the life of your board, we recommend using our
own Sigel accessories.
Sigel GmbH does not assume any responsibility or guarantee for boards that have been incorrectly mounted or for any resulting damage.
GUARANTEE
* We offer a 25-year guarantee that the glass surface will remain perfect to write on and to clean. We guarantee that the magnetic glass board will
remain easy to wipe and free of smudges and other residue when using Sigel accessories and following our instructions for use. This guarantee does
not apply in cases of mistreatment, negligence, incorrect usage or other methods of utilisation that do not comply with the enclosed instructions.
MAGNETS
➔ Due to the thickness of the glass, only the enclosed SuperDym neodymium magnets or other extra-strong magnets can be used.
➔ If the distance between them is too small (< 10 cm), the magnets can collide, causing the magnetic coating to chip or the magnets
to splinter.
➔ Danger of injury: fingers or skin can be squashed between two magnets, resulting in bruising.
➔ Magnets create a strong, far-reaching magnetic field. There is a risk of damage to cards with a magnetic strip, electronic appliances
(data carriers, mobile phones, computer, monitors, etc.), mechanical watches and hearing aids.
➔ People with pacemakers and heart defibrillator implants should avoid magnetic fields.
➔ Magnets are not a toy! Keep them out of the reach of children – small parts are a choking hazard.
5