Start/Stop Button - magnetic Revolution Manuel

GB
Applications
The Magnetic Revolution File is designed for all nail filing techniques (for
removing of old enhancements, buffing and sculpting etc). Read – for your
own benefit – the following conditions regarding the instructions and warranty
of your Revolution File. Keep the instructions near the electric file for everyone
to read who uses the machine.
Specifications controller:
Model: Revolution
Input: AC 230 V 50 Hz 27VA
Output: DC 3 – 30 V 0.2 – 0.4A
Dimensions: w 117 mm x d 147 mm x h 89 mm
Weight: 1,4 kg
Specifications hand piece:
Rotation Speed max.: 30.000 rpm / DC 30 V
Dimensions: diameter 23.6 mm (max), length 129 mm
Weight: 180 gram (not including cord)
The specifications and designs in this instruction manual are
subject to change without notice.
Safety Precautions
• Please work safe and responsible. Knitted gloves, clothes with open cuffs
and long hair are likely to being caught in the machine.
• Please wear goggles to prevent dust and particles from getting in the eyes.
In addition, please wear a disposable mouth mask to prevent breathing in
dust and particles.
• Please use the machine in a dry, ventilated space with a temperature
between 0 and 40 degrees Celcius with an average humidity varying
between 20 to 80% (no condensation). Never use the machine in a wet or
humid place. Moisture can cause short circuiting, fire or rust.
• During operation, sparks of fire can occur in the hand piece. Never use the
machine near flammable or explosive materials such as lacquer, paints,
thinner, gasoline, gas, adhesives et cetera.
• Please make sure cord and plug are not damaged to prevent current
leakage, shocks or fire. Always check cords and cables before starting the
machine. Let a broken cord be repaired by a professional.
• Use the machine in a clean, tidy place to avoid tripping over cords.
• Please use bits with specified standard for the machine. Please work within
the permitted range of rotation.
• Please do not place a cloth or anything else on the ventilation slits of the
machine. Also, please avoid using the machine while any dust is attached
around the ventilation holes.
• Avoid contact with flammable materials like alcohol, oil and other liquids.
• Please do not blow compressed air into ventilation holes of the machine.
• Turn off the machine during absence.
• Keep the machine out of reach of children.
• Never operate the machine without a bit.
• When operating an electric file, we urgently advice you to use a built-in
table vent.
• Never change anything to the machine that could affect the original
functionality or safety.
• Never use the machine for other purposes than described.
Precautions while at work
• Please ensure that all parts of the machine are firmly connected before use.
Turn the speed button to MINUS, hold the hand piece firmly and press the
on-off button to increase the speed slowly.
• Never use the machine under the specified Voltage (230V)
• Turn off the machine while changing the tools.
• Keep, hands, eyes and face on a safe distance while the machine is working.
• Turn the machine off immediately when feeling abnormal movement during
operation.
• Do not operate the file when the bit is not locked. It may damage the hand
piece.
• Replace a protective bit after use to prevent troubles.
• Keep moving the bit constantly, don't keep the bit on the same spot of
the nail.
• Please do not press the bit too much while rotating. It does not only work
inefficient but it could also damage the bit and nail.
• Do not drop the hand piece. If it happens, ensure yourself of a normal
appearance of the tool and bit and then operate increasing the speed from
the [MIN] position gradually. If something unusual is detected, contact
your supplier.
Maintenance and inspection
• Remove dust or dirt with a brush or soft cloth after use. After that use a
moist towel. Dry off with a duster. If there is dirt on the inside of the collet,
remove the collet from the head and clean it.
• Use dust protectors to prevent dust from damaging your hand piece.
• Never place a dust protector against the hand piece, leave some space in
between.
• Always remove the bit from the hand piece when you are finished working.
Replace by the protective bit.
• Disinfect your bits according to the guidelines of your supplier.
• Periodical inspection is recommended every 1 or 2 years for safe and
efficient use. Please consult your service supplier.
Instructions for the controller
Parts identification / connection
1. Power button
2. Speed control knob
3. Output jack
4. Hand piece holder
5. Forward lamp
6. Rotation selection button
7. Pilot / overload lamp
8. Reverse lamp

9. Start/stop button

10. Start lamp
11. Variable foot controller jack
12. AC plug
1. Connect the hand piece to the output jack (3)
2. If required, connect variable foot controller (VC70)
3. Ensure that the power button (1) is turned off before connecting the AC
plug (12) to the power supply.
Operation
1. Press the power button (1). The green power led (7) will light up.
2. Push rotary selection button (6) to move forward or reverse.
3. Hold the hand piece firmly and push the start/stop button (9). The
green start led will light up and the hand piece will start rotating. To stop