Product Description And Specifications - Casals CCS190L Notice Originale

Product description and Specifications

Description
A HM saw blade
B Spindle blocking button
C Mobile blade guard
D Saw blade setting disc
E Disc setting screw
F Depth setting lever
G Lateral stop setting wing nut
H Safety push button switch
I On-/off switch
J Angular cutting lever
K Cutting line guide
L Sawdust extraction
M Lateral Stop
O Laser Switch
P Laser Light and Led work Light
Instructions for use
Before use:
- Make sure that all the product's packaging has been
removed.
- Prepare the appliance according to the function you
wish to use:
Fitting the disc
- Unplug the appliance from the mains before replacing
any accessory.
WARNING! : Always unplug the machine before carrying
out any work on it.
CAUTION: Do not use bent or cracked blades or high-
speed steel blades. Do not use saw blades that do
not conform to the specifications contained in these
instructions.
WARNING! Never press the blocking button B when
the machine is running. The shaft must have stopped
completely before the blocking button B is pressed.
1. Move the mobile guard (C) backwards and hold it in
place.
2. To loosen or tighten screw (E) with the key supplied
with the machine, block the screw press by pushing block
button (B).
3. Loosen the screw (E) and remove the setting disc (D).
4. Fit the saw blade and tighten with the setting disc (D)
and the screw (E).
6
4.1 To adapt saw discs with a 20 or 30mm hole diameter
(come with the machine), first fit the washer that
corresponds to the diameter of the saw disc you are
using, next the saw disc and screw them into place with
fastening disc (D) and screw (E).
5. Before fitting the new blade, make sure the surfaces
in contact with the setting discs are clean. (The arrow
printed on the fixed guard of the machine indicates the
cutting direction of the teeth).
6. Once the disc is fitted, check that the blocking button
(B) has returned to its original position due to movement
of the incorporated spring.
- In order to remove disc, follow the same steps as
indicated previously but in reverse order.
Dust extraction Assembly
- Always use the appliance with the dust collector
connected, inhaling dust is harmful to your health.
- Connect the vacuum aspirator suction tube to the dust
extraction adaptor (L)
Use:
Cutting depth setting
- To adjust the cutting depth, loosen the lever (F) and
move the base upwards or downwards. The scale printed
on the base indicates the cutting depth
Cutting angle setting
It can cut vertically and with an inclination of up to 45º.
The angle is adjusted by loosening the lever (J) and
according the scale printed on the base.
Cutting indication
The notch (K) is used as a cutting indication with the
blade in a vertical position or 45º. It is advisable to make
test cuts.
Lateral stop adjustment
For parallel cutting, use the lateral stop (M). Cutting width
is adjusted with the scale or according to the plotting.
Tighten the wing nut (G) to work with the lateral stop.
- Connect the appliance to the mains.
- Press the locking button (H), and squeeze the trigger in
the on/off switch (I). When the on/off switch is released,
the machine stops.
Use laser Generator and LED work light (Fig 1)
- CAU
Class
- Do n
ensur
for lon
- Alwa
piece
sheet
the re
opera
- Only
- Turn
- Dep
will sw
- If yo
the la
Once
- Stop
Maint
WARN
out wo
- Che
on the
alway
- Insp
moun
Shoul
to do
- Moto
over t
dama
- The
obsta
- Clea
motor
- Che
is not,
replac
- Disc
cool b
- Clea
conne
IMME
- Clea
of was
- Do n
pH su
the ap
- Do n
avoid
- Neve