Casals CCS190L Notice Originale page 3

English
Circular Saw
CCS190L
Dear Customer,
Many thanks for trusting to Casals Professional.
Thanks to its continuous effort, our innovation and the
strictest quality controls, Casals Professional develops
electric Power Tools for the toughest jobs.
Read these ORIGINAL instructions carefully before
switching on the appliance and keep them for future ref-
erence. Failure to follow and observe these instructions
could lead to an accident.
GENERAL POWER TOOLS SAFETY WARNING
WARNING Read all safety warnings and all in-
structions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cord-
less) power tool.
Work Area Safety
- Keep the working area clean and well lit. Cluttered and
dark areas invite accidents.
- Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
- Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control
- CAUTION: In order to prevent overheating do not cover
the appliance.
- Ensure that neither the air access nor exit become either
totally or partially covered by drapery, clothing, etc., as this
increases the risk of fire.
Electric safety
- Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges or
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded
- Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
- Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
- When operating the power tool outdoors, use an
extension cord suitable for outdoor use. Use a cord
suitable for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
- Do not use the appliance if the cable or plug is damaged.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the
appliance.
- Only use the appliance with the specific electric
connector provided.
- If any of the appliance casings breaks, immediately
disconnect the appliance from the mains to prevent the
possibility of an electric shock.
- Do not use the appliance if it has fallen on the floor, if
there are visible signs of damage or if it has a leak.
- CAUTION: Maintain the appliance dry.
- CAUTION: Do not use the appliance near water.
- Do not use the appliance with damp hands or feet, or
when barefooted.
- Do not wrap the power cord around the appliance.
- Do not clip or crease the power cord.
- Check the state of the power cord. Damaged or tangled
cables increase the risk of electric shock.
- Do not touch the plug with wet hands.
Personal safety
- Stay alert, Watch you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
- Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
- Prevent unintentional starting. Ensure the switch
is in the off-position before connecting the power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energizing power tools that have the switch on
invites accidents.
- Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injur.
- Do not overreach. Keep proper footing and balance
at all times.
- This enables better control of the power tool in
unexpected situations
ORIGINAL instructions
3