Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Removing
To remove the deflector (15), pull the deflector to the rear
and off the outlet.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Warning! Let the tool work at its own pace. Do not overload.
Variable speed control (fig. G)
The variable speed control (1) allows you to adapt the speed
of the tool to the workpiece material.
Use a low speed setting when using a fine grit, when working
with plastics or ceramics and when removing painted or
varnished surfaces.
Use a high speed setting when using a coarse grit and when
removing a lot of material.
Set the variable speed control knob (1) to the required
setting.
Switching on and off (fig. G)
To switch the tool on, press the on/off switch (2).
To switch the tool off, release the on/off switch (2).
For continuous operation:
- Press the on/off switch (2).
- Press the lock-on button (3).
- Release the on/off switch (2).
To switch the tool off when in continuous operation, press
and release on/off switch (2).
Emptying the dust cassette (fig. F)
The dust cassette (14) should be emptied every 10 minutes.
Pull the dust cassette (14) to the rear and off the tool.
Remove the cover (19) by twisting it counter-clockwise.
Hold dust cassette (14) with the filter (18) facing down and
shake the cassette (14) to empty the contents.
Shake the cover (19) to empty the contents.
Refit the cover (19) onto the dust cassette (14), twisting it
clockwise until it locks into place.
Refit the dust cassette (14) onto the tool.
Cleaning the dust cassette filter (fig. F) (Where supplied)
Warning! Do not brush or use compressed air or sharp objects
to clean the filter. Do not wash the filter.
The dust cassette filter (18) is re-usable & should be
cleaned regularly.
Empty the dust cassette (14) as described above.
Pull the filter (18) off the dust cassette (14).
Shake off the excess dust by tapping the filter (18) into a
dustbin.
Replace the filter (18).
Fit the cover (19).
Slide the dust cassette (14) on to the tool and make sure
that it is securely located.
Emptying the dustbag (fig. E) (Where supplied)
The dustbag (13) should be emptied every 10 minutes of
use.
Pull the dustbag (13) to the rear and off the tool.
Hold the spout down and shake the dustbag (13) to empty
the contents.
Slide the dustbag (13) on to the tool and make sure that it
is securely located.
If necessary, the dustbag (13) can be removed from its frame
and washed. Let it dry before refitting it.
Special applications (fig. H, I and J)
Cranked arm (fig. H) (Where supplied)
Use section A for grooving or sanding in the centre of
workpieces and in confined areas. Use section B for curved
surfaces.
Straight arm (fig. I)
Use the normal or narrow arms for general use, for slotting
and for making joints.
Narrow arm (fig. J) (Where supplied)
Use the narrow arm for finer detail, for cutting and for
carving.
Hints for optimum use
Always hold the tool with both hands.
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding belt (12).
Replace when necessary.
Always sand with the grain of the wood.
When sanding new layers of paint before applying another
layer, use extra fine grit.
ENGLISH
9
Publicité
Table des Matières
