Important Instructions; Assembly Instruction - TZS First AUSTRIA FA-5560-3 Mode D'emploi

INSTRUCTION MANUAL
• Please read the instruction manual carefully
and keep it for future use.

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electrical shock, burns
and other injury, including the following:
1. Study this instruction manual carefully before
using the product.
2. The device is only intended for private and
not for any commercial use.
3. Remove the unit from its packaging and check
to make sure it is in good condition before
using.
4. Do not let children play with parts of the
packing (such as plastic bags).
5. Check the household voltage to ensure it
matches the fan's rated specification.
6. Check the power cord and plug carefully
before use to make sure that they are not
damaged.
7. Before unplugging the power cord, be sure to
turn off the power. When touching the unit,
be sure your hands are dry to prevent from
electric shock.
8. Do not run the cord under carpeting. Do not
cover cord with throw rugs,runners or the like.
Arrange cord away from traffic area and where
it will not be tripped over.
9. Do not use a soft surface, like a bed, where
openings may become blocked.
10. Avoid the use of an extension cord because
the extension cord may overheat and cause a
risk of fire.
11. Do not use outdoors.
12. Avoid contact with moving parts. Keep hands,
hair, clothing, spatulas and other utensils away
during operation to reduce the risk of injury to
persons and/or damage to the machine.
13. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
14. Children should be supervised to ensure that
they do not play with the appliance.
CAUTIONS
• This appliance is not a toy.
• To avoid the risk of fire or electric shock do not
remove the housing by yourself.
• Any servicing other than cleaning and user
maintenance should be performed by an
authorized service representative.
• If the supply cord is damaged, it must be
replaced by a special cord or assembly
available from the manufacturer or its service
agent.
• Repair should be done by an authorized
service personal only.
• To reduce the risk of electric shock, do not
immerse or expose the product, flexible cord
or plug to rain, moisture or any liquid.
• Do not operate the appliance with wet hands,
in order to avoid damage.
• Do not use the appliance near explosive and
combustible gas.
• Do no turnover the appliance. Unplug the
power supply If it is toppled over and there
have some water in the body. Dry the body
before use.
• Do not knock or shake the body when use,
otherwise it may cause stop.
• The appliance must not located immediately
below a socket outlet.
• The rating current of socket should exceed
10A.
• Do not use the appliance in the immediate
surrounding of a bath, a show or a swimming
pool.
• Don't keep the device in the watery
environment;
• Keep the device away the place of high
temperature, ray and wetly.
• Please turn off the power supply in the watery
environment.
• In the event where the appliance is dropped
into the water, turn off the power at the power
outlet and remove the plug immediately. DO
NOT REACH INTO THE WATER TO RETRIEVE IT.
• It is important to note that the appliance will
have to be inspected by a qualified technician
before using it again.
2
COMPONENTS DIAGRAM
(Fig. A)
TOUCH BUTTON AND DISPLAY SYMBOL
1. Low lamp
2. Power lamp
3. Normal lamp
4. Natural lamp
5. Swing button
6. Receiver
7. Speed button
8. On/off button
9. Middle lamp
10. High lamp
11. Timer lamp
12. Sleep lamp
13. Timer button
14. Temp, display
15. Mode button
16. Control panel
17. Top
18. Air outlet
19. Front shell
20. Front base
21. Handle
22. Back shell
23. Air inlet
24. Rear base
25. Power cord
26. Remote control

ASSEMBLY INSTRUCTION

1. Unpack and remove the tower fan. Please
assemble it correctly according to the order
when using it; and keep the packaging
materials in a safe place for storage.
2. Check if the parts in the package match the
packing list in the manual.
3. Install the front and rear bases (as shown).
STEP 1-3 (Fig. B)
1. Front base
2. Body
3. Power cord
4. Rear base
5. Square hole
6. Screw here
Please assemble correctly in order when using;
and keep the packaging materials in a safe place
for storage.
(Step 1) First place the power cord into the center
hole of the front and rear bases, and then close
the front and rear bases, as in step 2;
(Step 2) Pass the power cord through the middle
hole of the rear base;
(Step 3) Align the square hole on the assembled
base with the square boss on the body, and screw
the screw to the hole with a screwdriver to put the
product into the product.
4. Check if the power supply is consistent with
the parameters on the nameplate of the unit,
and plug the power cord into the power
socket. At this time, the whole machine will
issue "di".
One sound, the power indicator light is on,
indicating that the whole machine is powered;
(Note: Do not plug or unplug with wet hands
to avoid danger caused by electric shock.
When moving the machine, unplug the power
supply).
5. Press the " " button on the product control
panel: the product enters the mid-range work
by default. At the same time, the mid-range
indicator and the room temperature indicator
light up, and the display shows the room
temperature.
6. According to the " " button on the product
control panel, the product corresponds to the
low- mid-high , the corresponding indicator
Corresponding to light.
7. Press the " " button on the product control
panel, the product enters the timing setting
state, the display time is displayed on the
display, the timing indicator lights up,
continue to press this button, from 0H to 8H, H
is hour, and the minimum time interval is After
1 hour, the set time display time is 5 seconds,
the timing setting is successful, and the display
continues to display the indoor temperature.
8. Press the " " button on the product control
panel to enter the mode function switch.
Press once, the tower fan enters the normal
wind mode, press the tower fan again to
enter the natural wind mode, and then press
the tower fan to enter the sleep wind mode,
corresponding to the indicator light. Light up.
9. Press the " " button on the control panel
of the product, then the tower fan will swing
back and forth to swing the air, and the head
light will light up. Press the it again, the tower
fan stops swinging, and the moving head
indicator light goes out.
10. The function corresponding to the remote
control is the same as the button control
function.
11. If you want to turn off the tower fan, press the
" " button on the control button, the tower
fan will stop working. If it is not used for a long
time, be sure to unplug the power cord from
the outlet.
3