Using Passive Crossovers; Remote Punch Bass - Rockford Fosgate 550X Manuel D'installation Et D'utilisation

USING PASSIVE CROSSOVERS

A passive crossover is a circuit that uses capacitors and/or coils and is placed on speaker leads
between the amplifier and speaker. The crossover delegates a specific range of frequencies to the
speaker for optimum driver performance. A crossover network can perform one of three functions:
High-Pass (capacitors), Low-Pass (inductors or coils) and Bandpass (combination of capacitor and
coil).
The most commonly used passive crossover networks are 6dB/octave systems. These are easy to
construct and require one component per filter. Placing this filter in series with the circuit will
reduce power to the speaker by 6dB/octave above or below the crossover point depending on
whether it is a high-pass or low-pass filter. More complex systems such as 12dB/octave or
18dB/octave can cause impedance problems if not professionally designed.
Passive crossovers are directly dependent upon the speaker's impedance and component value for
accuracy. When passive crossover components are used in multiple speaker systems, the crossover's
effect on the overall impedance should be taken into consideration along with the speaker's
impedance when determining amplifier loads.
CAUTION: These amplifiers are not recommended for impedance loads below 2Ω
!
stereo and 4Ω bridged (mono).
L
6dB/Octave Low-Pass
C
6dB/Octave High-Pass
L = Low-Pass (Inductor)
C = High-Pass (Capacitor)
For more information, see your
Authorized Rockford Fosgate Dealer.

REMOTE PUNCH BASS

Mounting and installation
1. Find a location, either under the dash or
near the center console, that gives easy
access to the remote.
2. Using the screws supplied, install the
mounting clip with the tabs towards the
back.
3. Route the cable for the remote and connect
to both the remote and amplifed subwoofer.
4. Slip the remote onto the mounting clip until
it snaps into place.
5. Install the decal and knob onto the remote.
Speaker Impedance
Freq.
2 OHMS
Hertz
L C
80 4.1mH 1000mF
100 3.1mH 800mF
130 2.4mH 600mF
200 1.6mH 400mF
260 1.2mH 300mF
400 .8mH 200mF
600 .5mH 136mF
800 .41mH 100mF
1000 .31mH 78mF
1200 .25mH 66mF
1800 .16mH 44mF
4000 .08mH 20mF
6000 51mH 14mF
9000 34mH 9.5mF
12000 25mH 6.6mF
Mounting
Clip
Knob
Decal
I
NSTALLATION
4 OHMS
L C L
8.2mH 500mF 16mH
6.2mH 400mF 12mH
4.7mH 300mF 10mH
3.3mH 200mF 6.8mH
2.4mH 150mF 4.7mH
1.6mH 100mF 3.3mH
1.0mH 68mF 2.0mH
.82mH 50mF 1.6mH
.62mH 39mF 1.2mH
.51mH 33mF 1.0mH
.33mH 22mF .68mH
.16mH 10mF .33mH
.10mH 6.8mF .20mH
68mH 4.7mF .15mH
51mH 3.3mF 100mH
8 OHMS
C
250mF
200mF
150mF
100mF
75mF
50mF
33mF
26mF
20mF
16mF
10mF
5mF
3.3mF
2.2mF
1.6mF
9