Publicité
Les langues disponibles
Les langues disponibles
AKASA Mounting Frame int. 3.5" / 2.5"
Item no. 41 60 83
1.
Intended use
This product enables installation of 8.89 cm (3.5") devices and 8.89 cm (3.5") or 6.35 cm (2.5")
hard drives in 13.34 cm (5.25") slots.
For safety purposes, you must not rebuild and/or modify this product. If you use the product for
purposes other than those described above, the product may be damaged. Read the instructions
carefully and keep them. Make this product available to third parties only together with its
operating instructions.
2.
Delivery content
•
Mounting frame
•
4 x screws for 8.89 cm (3.5") device or 6.35 cm (2.5") hard drive
•
4 x screws for 8.89 cm (3.5") hard drive
•
4 x screws for 13.34 cm (5.25") slot
•
Operating instructions
•
Manufacturer's instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
Persons / Product
•
Grasp the hard disk laterally in the housing, do not touch the plate with the electronics.
Electrostatic discharge can destroy the hard disk.
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
•
Also observe the safety and operating instructions of any other devices which are connected
to the product.
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
•
If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
4.
Installation
Before installing the mounting frame, make sure to turn off the computer,
switch off the main switch on the back of the power supply unit and unplug the
mains plug. Since there is still voltage even when the computer is switched off,
there is a risk of electric shock when touching electric components inside.
If you have no specialist knowledge in installing this product, please arrange for
installation to be carried out by a specialist or a suitable specialist workshop.
Detailed illustrations on how to proceed with the installation and information on the
screws included in delivery can be found in the manufacturer's instructions.
Ground yourself with a grounding mat or anti-static wristbands to prevent electrical static
discharge (ESD) from your body and clothes during installation. Integrated circuits are sensitive
to electrical static. They can be damaged or destroyed if ESD occurred.
Installation of an 8.89 cm (3.5") device
1.
Remove the small panel from the mounting frame by pressing the two plastic catches on the
panel's outer faces inwards and thus releasing it.
2.
Insert an 8.89 cm (3.5") device with the panel facing outwards through the mounting frame's
opening.
3.
Secure the device with four screws through the four lateral screw openings.
Installation of an 8.89 cm (3.5") hard drive
1.
Remove the large panel from the mounting frame by pressing the four plastic catches on the
panel's outer faces inwards and thus releasing it.
Version 11/11
2.
Put an 8.89 cm (3.5") hard drive on the mounting frame so that it is flush with the frame's
front side.
3.
Turn the frame with the hard drive around, holding the hard drive tight.
4.
Secure the hard drive using four screws on the four outer screw openings at the bottom side
of the mounting frame.
Installation of a 6.35 cm (2.5") hard drive
1.
Put a 6.35 cm (2.5") hard drive in the centre of the mounting frame so that it is flush with the
frame's rear side.
2.
Turn the frame with the hard drive around, holding the hard drive tight.
3.
Secure the hard drive using four screws on the four outer screw openings at the bottom side
of the mounting frame.
Installation of the mounting frame in the 13.34 cm (5.25") slot
1.
Mount an 8.89 cm (3.5") device, a 6.35 cm (2.5") hard drive or an 8.89 cm (3.5") hard drive
on the mounting frame.
2.
Open the PC housing.
3.
Insert the frame with the panel, i.e. the front side facing outwards into a 13.34 cm (5.25") slot
on your PC.
4.
Hold the frame tight and secure it with four screws in the lateral screw openings.
5.
Connect the mounted device to the PC.
5.
Technical data
Suitable for:
Dimensions (W x H x D):
Weight:
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2011 by Conrad Electronic SE.
8.89 cm (3.5") device / 6.35 cm (2.5") hard drives /
8.89 cm (3.5") hard drives
149 x 42.2 x 154.5 mm
105 g
V1_1111_02-JU
Publicité
